Главная Справочники HPE Managed Switches

HPE FlexFabric 11900 Switch Series: технические характеристики и документация

Нужна помощь с конфигурацией?

Пришлите SKU, спецификацию или список требований. Специалист Apltech проверит совместимость компонентов и найдёт актуальные артикулы

Получить консультацию →

HPE FlexFabric 11900 Switch Series: технические характеристики и документация

В архиве

HPE FlexFabric 11900 Switch Series

Overview

HPE FlexFabric 11900 Switch Series

Models
HPE FlexFabric 11908 V Switch Chassis	JG608A

Key features
High-performance CLOS-based switching architecture Large layer 2 scaling with TRILL and HPE IRF Feature-rich routing with IPv4/IPv6, MPLS, and QoS Enhanced modularity with control and data plane separation High performance with 1/10GbE, 40GbE and 100GbE across 7.7 Tbps switch fabric

Product overview
The HPE FlexFabric 11900 Switch Series is a high-performance data center aggregation switch that provides line-rate, high-density 10GbE and 40GbE connectivity designed for cost-effective end-of-row (EoR) and small core deployments. With latency as low as 3 µs, the HPE FlexFabric 11900 Switch Series can scale to 384 1/10GbE, 192 1/10GBASE-T, 64 40GbE or 16 100GbE ports. The switch delivers up to 7.7 Tbps switching capacity and 5.8 Bpps forwarding throughput. A broad variety of interface options is available, including 1/10GbE, 1/10GBASE-T, 40GbE and 100GbE. Ready for software-defined networking (SDN), the switch supports full Layer 2 and 3 features, including advanced features such as transparent Interconnection of Lots of Links (TRILL) and Intelligent Resilient Fabric (IRF), which provides the ability to build large, resilient switching fabrics. The HPE FlexFabric 11900 Switch Series also supports fully redundant and hot-swappable components to complement its other enterprise-class capabilities.

Features and benefits

Data center optimized

Scalable Layer 2 fabrics
builds flexible, resilient and scalable Layer 2 fabrics with TRILL together with HPE IRF
Multitenant Device Context (MDC)
virtualizes a physical switch into multiple logical devices, with each logical switch having its own processes, configuration, and administration
Data Center Bridging (DCB) protocols
supports IEEE 802.1Qaz Data Center Bridging Exchange (DCBX) and Enhanced Transmission Selection (ETS) and IEEE 802.1Qbb Priority Flow Control (PFC) for converged fabrics
Fibre Channel over Ethernet (FCoE) capabilities
delivers support for FCoE, including expansion, fabric, trunk VF and N ports, and aggregation of E-port and N-port virtualization
Edge Virtual Bridging (EVB) with Virtual Ethernet Port Aggregator (VEPA) support
provides connectivity into the virtualization-ready data center environment
Front-to-back airflow design
accomodates deployment in data centers utilizing hot-cold aisles

Performance

High-performance fully-distributed architecture
delivers up to 7.7 Tbps switching capacity and 5.76 Bpps throughput with non-blocking wire-speed performance and latency as low as 3 microseconds
High-density 1/10GbE and 40GbE interface connectivity
offers up to eight interface module slots to scale up to 384 1GbE/10GbE and 64 40GbE ports
Scalable system design
provides investment protection to support future technologies and higher-speed connectivity, as the switch is designed for increased backplane bandwidth

Product architecture

Advanced Comware modular operating system
brings native high stability, independent process monitoring and restart through the modular design and multiple processes of HPE Comware v7 software; supports enhanced serviceability functions
In-Service Software Upgrade (ISSU)
provides an upgrade of the entire chassis, or an individual task or process, with zero packet loss
Distributed architecture with separation of data and control planes
delivers enhanced fault tolerance and facilitates continuous operation and zero service disruption during planned or unplanned control-plane events

Resiliency and high availability

Intelligent Resilient Fabric (IRF)
creates virtual resilient switching fabrics, where two or more switches perform as a single L2 switch and L3 router; switches do not have to be co-located and can be part of a disaster-recovery system; servers or switches can be attached using standard LACP for automatic load balancing and high availability; can eliminate the need for complex protocols like Spanning Tree Protocol, Equal-Cost Multipath (ECMP), or VRRP, thereby simplifying network operation
Redundant/load-sharing fabrics, management, fan assemblies, and power supplies
increases total performance and power available while providing hitless, stateful failover
Hot-swappable modules
allows replacement of modules without any impact on other modules
Graceful restart
allows routers to indicate to others their capability to maintain a routing table during a temporary shutdown and significantly reduces convergence times upon recovery; supports OSPF, BGP, and IS-IS
Virtual Router Redundancy Protocol (VRRP)
allows groups of two routers to dynamically back each other up to create highly available routed environments
Device Link Detection Protocol (DLDP)
monitors link connectivity and shuts down ports at both ends if unidirectional traffic is detected, preventing loops in STP-based networks
Hitless patch upgrades
allows patches and new service features to be installed without restarting the equipment, increasing network uptime and facilitating maintenance
IEEE 802.3ad Link Aggregation Control Protocol (LACP)
supports up to 1024 trunk groups and up to 16 members per trunk; supports static or dynamic groups and a user-selectable hashing algorithm
Passive design system
delivers increased system reliability as backplane has no active components
Ultrafast protocol convergence (subsecond) with standard-based failure detection—Bidirectional Forwarding Detection (BFD)
enables link connectivity monitoring and reduces network convergence time for RIP, OSPF, BGP, IS-IS, VRRP, MPLS, and IRF

Layer 2 switching

VLAN
supports up to 4,094 port-based or IEEE 802.1Q-based VLANs; also supports MAC-based VLANs, protocol-based VLANs, and IP-subnet-based VLANs for added flexibility
Bridge Protocol Data Unit (BPDU) tunneling
transmits Spanning Tree Protocol BPDUs transparently, allowing correct tree calculations across service providers, WANs, or MANs
Port mirroring
duplicates port traffic (ingress and egress) to a local or remote monitoring port; supports four mirroring groups, with an unlimited number of ports per group
Spanning Tree Protocol (STP)
supports standard IEEE 802.1D STP, IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) for faster convergence, and IEEE 802.1s Multiple Spanning Tree Protocol (MSTP)
Internet Group Management Protocol (IGMP) and Multicast Listener Discovery (MLD) protocol snooping
controls and manages the flooding of multicast packets in a Layer 2 network
IEEE 802.1ad QinQ and selective QinQ
increase the scalability of an Ethernet network by providing a hierarchical structure; connect multiple LANs on a high-speed campus or metro network
Per-VLAN Spanning Tree Plus (PVST+)
allows each VLAN to build a separate spanning tree to improve link bandwidth usage in network environments with multiple VLANs
Isolation at data link layer with private VLANs
provides, through a two-tier VLAN structure, an additional layer of protection, simplifying network configuration while saving VLAN resources

Layer 3 routing

Open shortest oath first (OSPF)
delivers faster convergence; uses this link-state routing Interior Gateway Protocol (IGP), which supports ECMP, NSSA, and MD5 authentication for increased security and graceful restart for faster failure recovery
Intermediate system to intermediate system (IS-IS)
uses a path vector Interior Gateway Protocol (IGP), which is defined by the ISO organization for IS-IS routing and extended by IETF RFC 1195 to operate in both TCP/IP and the OSI reference model (Integrated IS-IS)
Border Gateway Protocol 4 (BGP-4)
delivers an implementation of the Exterior Gateway Protocol (EGP) utilizing path vectors; uses TCP for enhanced reliability for the route discovery process; reduces bandwidth consumption by advertising only incremental updates; supports extensive policies for increased flexibility; scales to very large networks
Multiprotocol Label Switching (MPLS)
uses BGP to advertise routes across Label Switched Paths (LSPs), but uses simple labels to forward packets from any Layer 2 or Layer 3 protocol, which reduces complexity and increases performance; supports graceful restart for reduced failure impact; supports LSP tunneling and multilevel stacks
Dual IP stack
maintains separate stacks for IPv4 and IPv6 to ease the transition from an IPv4-only network to an IPv6-only network design
Equal-Cost Multipath (ECMP)
enables multiple equal-cost links in a routing environment to increase link redundancy and scale bandwidth
Policy-based routing
makes routing decisions based on policies set by the network administrator
Static IPv4 routing
provides simple manually configured IPv4 routing
Routing Information Protocol (RIP)
uses a distance vector algorithm with UDP packets for route determination; supports RIPv1 and RIPv2 routing; includes loop protection
IP performance optimization
provides a set of tools to improve the performance of IPv4 networks; includes directed broadcasts, customization of TCP parameters, support of ICNP error packets, and extensive display capabilities
Unicast Reverse Path Forwarding (uRPF)
limits erroneous or malicious traffic in accordance with RFC 3074
Static IPv6 routing
provides simple, manually configured IPv6 routing Routing Information Protocol next generation (RIPng) extends RIPv2 to support IPv6 addressing
OSPFv3
provides OSPF support for IPv6
IS-IS for IPv6
extends IS-IS to support IPv6 addressing
BGP+
extends BGP-4 to support Multiprotocol BGP (MBGP), including support for IPv6 addressing
Multiprotocol Label Switching (MPLS) Layer 3 VPN
allows Layer 3 VPNs across a provider network; uses MP-BGP to establish private routes for increased security; supports RFC 2547bis multiple autonomous system VPNs for added flexibility
Multiprotocol Label Switching (MPLS) Layer 2 VPN
establishes simple Layer 2 point-to-point VPNs across a provider network using only MPLS Label Distribution Protocol (LDP); requires no routing and therefore decreases complexity, increases performance, and allows VPNs of non-routable protocols; uses no routing information for increased security; supports Circuit Cross Connect (CCC), Static Virtual Circuits (SVCs), Martini draft, and Kompella-draft technologies
Virtual Private LAN Service (VPLS)
establishes point-to-multipoint Layer 2 VPNs across a provider
network
IPv6 tunneling
provides an important element for the transition from IPv4 to IPv6; allows IPv6 packets to traverse IPv4-only networks by encapsulating the IPv6 packet into a standard IPv4 packet; supports manually configured, 6to4, Intra-Site Automatic Tunnel Addressing Protocol (ISATAP) tunnels, and IPv6 on VPN to Provider Edge (6VPE) router tunnel

Quality of Service (QoS)

IEEE 802.1p prioritization
delivers data to devices based on the priority and type of traffic
Flexible classification
creates traffic classes based on access control lists (ACLs), IEEE 802.1p precedence, IP, and DSCP or Type of Service (ToS) precedence; supports filter, redirect, mirror, remark, and logging
Bandwidth shaping
- Port-based rate limiting
  provides per-port ingress-/egress-enforced increased bandwidth
- Classifier-based rate limiting
  uses an access control list (ACL) to enforce increased bandwidth
  for ingress traffic on each port
- Reduced bandwidth
  provides per-port, per-queue egress-based reduced bandwidth
Broad QoS feature set
provides support for Strict Priority Queuing (SP), Weighted Fair Queuing (WFQ), Weighted Deficit Round Robin(WDRR), SP+WDRR together, configurable buffers, Explicit Congestion Notification (ECN), and Weighted Random Early Detection (WRED)
Traffic policing
supports Committed Access Rate (CAR) and line rate

Layer 3 services

Address Resolution Protocol (ARP)
determines the MAC address of another IP host in the same subnet; supports static ARPs; gratuitous ARP allows detection of duplicate IP addresses; proxy ARP allows normal ARP operation between subnets or when subnets are separated by a Layer 2 network
User Datagram Protocol (UDP) helper
redirects UDP broadcasts to specific IP subnets to prevent server spoofing
Dynamic Host Configuration Protocol (DHCP)
simplifies the management of large IP networks and supports client and server; DHCP Relay enables DHCP operation across subnets

Management

Management interface control
enables or disables each of the following interfaces depending on security preferences: console port, Telnet port, or reset button
Industry-standard CLI with a hierarchical structure
reduces training time and expenses, and increases productivity in multivendor installations
SNMPv1, v2, and v3
provide complete support of SNMP; provide full support of industry-standard Management Information Base (MIB) plus private extensions; SNMPv3 supports increased security using encryption
sFlow (RFC 3176)
provides scalable ASIC-based wirespeed network monitoring and accounting with no impact on network performance; this allows network operators to gather a variety of sophisticated network statistics and information for capacity planning and real-time network monitoring purposes
Remote monitoring (RMON)
uses standard SNMP to monitor essential network functions; supports events, alarm, history, and statistics group plus a private alarm extension group
Debug and sampler utility
supports ping and traceroute for both IPv4 and IPv6
Network Time Protocol (NTP)
synchronizes timekeeping among distributed time servers and clients; keeps timekeeping consistent among all clock-dependent devices within the network so that the devices can provide diverse applications based on the consistent time
Network Quality Analyzer (NQA)
analyzes network performance and service quality by sending test packets, and provides network performance and service quality parameters such as jitter, TCP, or FTP connection delays and file transfer rates; allows a network manager to determine overall network performance and to diagnose and locate network congestion points or failures
Information center
provides a central information center for system and network information; aggregates all logs, traps, and debugging information generated by the system and maintains them in order of severity; outputs the network information to multiple channels based on user-defined rules
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
advertises and receives management information from adjacent devices on a network, facilitating easy mapping by network management applications

Connectivity

Jumbo frames
allows high-performance backups and disaster-recovery systems with a maximum frame size of 9k bytes
Loopback
supports internal loopback testing for maintenance purposes and an increase in availability; loopback detection protects against incorrect cabling or network configurations and can be enabled on a per-port or per-VLAN basis for added flexibility
Ethernet operations, administration and maintenance (OAM)
detects data link layer problems that occurred in the "last mile" using the IEEE 802.3ah OAM standard; monitors the status of the link between two devices
Monitor link
collects statistics on performance and errors on physical links, increasing system availability
Packet storm protection
protects against unknown broadcast, unknown multicast, or unicast storms with user-defined thresholds
Flow control
provides back pressure using standard IEEE 802.3x, reducing congestion in heavy traffic situations

Security

Access control list (ACL)
supports powerful ACLs for both IPv4 and IPv6; ACLs are used for filtering traffic to prevent unauthorized users from accessing the network, or for controlling network traffic to save resources; rules can either deny or permit traffic to be forwarded; rules can be based on a Layer 2 header or a Layer 3 protocol header; rules can be set to operate on specific dates or times
Remote Authentication Dial-In User Service (RADIUS)
eases switch security access administration by using a password authentication server
Terminal Access Controller Access-Control System (TACACS+)
delivers an authentication tool using TCP with encryption of the full authentication request, providing additional security
Secure shell (SSHv2)
uses external servers to securely log in to a remote device; with authentication and encryption, it protects against IP spoofing and plain-text password interception; increases the security of Secure FTP (SFTP) transfers
DHCP snooping
helps ensure that DHCP clients receive IP addresses from authorized DHCP servers and maintain a list of DHCP entries for trusted ports; prevents reception of fake IP addresses and reduces ARP attacks, improving security
IP Source Guard
filters packets on a per-port basis, which prevents illegal packets from being forwarded
ARP attack protection
protects against attacks that use a large number of ARP requests, using a host-specific, user-selectable threshold
Port security
allows access only to specified MAC addresses, which can be learned or specified by the administrator
IEEE 802.1X support
provides port-based user authentication with support for Extensible Authentication Protocol (EAP) MD5, TLS, TTLS, and PEAP with choice of AES, TKIP, and static or dynamic WEP encryption for protecting wireless traffic between authenticated clients and the access point
Multiple user authentication methods
- IEEE 802.1X
  uses an IEEE 802.1X supplicant on the client in conjunction with a RADIUS server to authenticate in accordance with industry standards
- Web-based authentication
  provides a browser-based environment, similar to IEEE 802.1X, to authenticate clients that do not support the IEEE 802.1X supplicant
- MAC-based authentication
  authenticates the client with the RADIUS server based on the client's MAC address

Multicast support

Internet Group Management Protocol (IGMP)
utilizes Any-Source Multicast (ASM) or Source-Specific Multicast (SSM) to manage IPv4 multicast networks; supports IGMPv1, v2, and v3
Protocol Independent Multicast (PIM)
defines modes of Internet IPv4 and IPv6 multicasting to allow one-to-many and many-to-many transmission of information; PIM Dense Mode (DM), Sparse Mode (SM), and Source-Specific Mode (SSM) are supported
Multicast Source Discovery Protocol (MSDP)
allows multiple PIM-SM domains to interoperate; is used for inter-domain multicast applications
Multicast Border Gateway Protocol (MBGP)
allows multicast traffic to be forwarded across BGP networks separately from unicast traffic

Integration

VPN 20Gbps 11900 Firewall Module
provides enhanced stateful packet inspection and filtering; supports flexible security zones and virtual firewall containment; delivers advanced VPN services with 3DES and AES encryption at high performance and low latency; offers Web content filtering and application prioritization and optimization

Warranty and support

1-year warranty
See http://www.hpe.com/networking/warrantysummary for warranty and support information included with your product purchase.
Software releases
to find software for your product, refer to http://www.hpe.com/networking/support; for details on the software releases available with your product purchase, refer to http://www.hpe.com/networking/warrantysummary

Configuration

Build To Order: BTO is a standalone unit with no integration. BTO products ship standalone are not part of a CTO or Rack-Shippable solution.

HPE FlexFabric 11908 V Switch Chassis		JG608A
Must select min 1 Interface Module Must select min 4 Fabric Modules Must select min 1 Management Module Must select min 1 Power Supply 20U - Height

Internal Power Supplies

System (std 0 // max 6) User Selection (min 1 // max 6) per switch enclosure

11900 provides 5+1 Redundancy. Select an appropriate number of power supplies based on the maximum output power of your system and redundancy requirements. For component power consumption consult the install guide.

HPE FlexFabric 11900 2500W AC Power Supply		JG616A
includes 1 x c19, 2500w		See Configuration NOTE:1, 2, 3

PDU Cable NA/MEX/TW/JP		JG616A#B2B
C19 PDU Jumper Cord (NA/MEX/TW/JP)

PDU Cable ROW		JG616A#B2C
C19 PDU Jumper Cord (ROW)

High Volt Switch to Wall Power Cord		JG616A#B2E
NEMA L6-20P Cord

HPE FlexFabric 11900 2400W DC Power Supply		JG617A
NEMA L6-20P Cord		See Configuration NOTE:1, 6

Configuration Rules

Note 1	If more than 1 power supply is selected they, must all be the same SKU number.

Note 2	Localization required on orders without #B2B, #B2C or #B2E options.

Note 3	#B2E is Offered only in NA, Mexico, Taiwan and Japan.

Note 6	One of these cables is required when ordering this power supply: (Use #B01 if switch is CTO) - if applicable
	HPE FlexNetwork 10500 48V 3m DC Power Supply Cable	JG390A
	HPE FlexNetwork 10500 48V 15m DC Power Supply Cable	JG391A

Remarks:	Drop down under power supply should offer the following options and results: Switch/Router/Power Supply to PDU Power Cord - #B2B in North America, Mexico, Taiwan, and Japan or #B2C ROW. (Watson Default B2B or B2C for Rack Level CTO) Switch/Router/Power Supply to Wall Power Cord - Localized Option (Watson Default for BTO and Box Level CTO) High Volt Switch/Router/Power Supply to Wall Power Cord - #B2E Option. (Offered only in North America, Mexico, Taiwan, and Japan)

Modules

Interface Modules

System (std 0 // max 8) User Selection (min 1 // max 8) per enclosure

HPE FlexFabric 11900 24-port 1/10GBASE-T SF Module		JG615A
No Transceivers

HPE FlexFabric 11900 32-port 10GbE SFP+ SF Module		JG611A
min=0 \ max=32 SFP+ Transceivers		See Configuration NOTE:1, 2, 4

HPE FlexFabric 11900 48-port 10GbE SFP+ SF Module		JG612A
min=0 \ max=48 SFP+ Transceivers		See Configuration NOTE:1, 2

HPE FlexFabric 11900 4-port 40GbE QSFP+ SF Module		JG613A
min=0 \ max=4 QSFP+ Transceivers		See Configuration NOTE:3

HPE FlexFabric 11900 8-port 40GbE QSFP+ SF Module		JG614A
min=0 \ max=8 QSFP+ Transceivers		See Configuration NOTE:3

HPE FlexFabric 11900 2-port 100GbE CFP SE Module		JG918A
min=0 \ max=2 CFP Transceivers		See Configuration NOTE:8

HPE 10500/11900/7500 20Gbps VPN Firewall Module		JG372A
min=0 \ max=2 SFP Transceivers		See Configuration NOTE:5

HP 10500/7500 20G Unified Wired-WLAN Module		JG639A
No supported Transceivers		See Configuration NOTE:7

Configuration Rules

Note 1	The following Transceivers install into this Module:
	HPE X170 1G SFP LC LH70 1550 Transceiver	JD109A
	HPE X170 1G SFP LC LH70 1570 Transceiver	JD110A
	HPE X170 1G SFP LC LH70 1590 Transceiver	JD111A
	HPE X170 1G SFP LC LH70 1610 Transceiver	JD112A
	HPE X170 1G SFP LC LH70 1510 Transceiver	JD115A
	HPE X120 1G SFP LC LH100 Transceiver	JD103A
	HPE X125 1G SFP LC LH40 1310nm Transceiver	JD061A
	HPE X120 1G SFP LC LH40 1550nm Transceiver	JD062A
	HPE X120 1G SFP RJ45 T Transceiver	JD089B
	HPE X120 1G SFP LC SX Transceiver	JD118B
	HPE X120 1G SFP LC LX Transceiver	JD119B
	HPE X125 1G SFP LC LH70 Transceiver	JD063B
	HPE X120 1G SFP LC BX 10-U Transceiver	JD098B
	HPE X120 1G SFP LC BX 10-D Transceiver	JD099B

Note 2	The following Transceivers install into this Module:
	HPE X130 10G SFP+ LC SR Transceiver	JD092B
	HPE X130 10G SFP+ LC LR Transceiver	JD094B
	HPE FlexNetwork X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable	JD095C
	HPE FlexNetwork X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable	JD096C
	HPE FlexNetwork X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable	JD097C
	HPE FlexNetwork X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable	JG081C
	HPE FlexNetwork X240 10G SFP+ SFP+ 7m Direct Attach Copper Cable	JC784C
	HPE X130 10G SFP+ LC ER 40km Transceiver	JG234A

Note 3	The following 40G Transceivers install into this Module:
	HPE X140 40G QSFP+ LC LR4 SM 10km 1310nm Transceiver	JG661A
	HPE X140 40G QSFP+ MPO SR4 Transceiver	JG325B
	HPE X140 40G QSFP+ MPO MM 850nm CSR4 300m Transceiver	JG709A
	HPE FlexNetwork X240 40G QSFP+ QSFP+ 3m Direct Attach Copper Cable	JG327A
	HPE FlexNetwork X240 40G QSFP+ QSFP+ 5m Direct Attach Copper Cable	JG328A
	HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 1m Direct Attach Copper Splitter Cable	JG329A
	HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 3m Direct Attach Copper Splitter Cable	JG330A
	HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 5m Direct Attach Copper Splitter Cable	JG331A

Note 4	The following Transceivers install into this Module:
	HPE X130 10G SFP+ LC LRM Transceiver	JD093B

Note 5	The following Transceivers install into this Module:
	HPE X125 1G SFP LC LH40 1310nm Transceiver	JD061A
	HPE X120 1G SFP LC LH40 1550nm Transceiver	JD062A
	HPE X125 1G SFP LC LH70 Transceiver	JD063B
	HPE X120 1G SFP LC SX Transceiver	JD118B
	HPE X120 1G SFP LC LX Transceiver	JD119B

Note 7	Maximum of this Module per Chassis: JG608A min=0\max=7 per Chassis There are no restrictions on which slots these modules may go in.
Note 8	The following Transceivers install into this Module:
	HP X150 100G CFP LC LR4 10km SM Transceiver	JG829A

Fabric Modules

System (std 0 // max 4) User Selection (min 4 // max 4) per enclosure

HPE FlexFabric 11908 1.92Tbps Type D Fabric Module		JG610A
No supported Transceivers

Management Modules

System (std 0 // max 2) User Selection (min 1 // max 2) per enclosure

HPE FlexFabric 11900 Main Processing Unit		JG609A

Remarks:	These modules can only be inserted into Slots 4 and 5.

Transceivers

SFP Transceivers

HPE X120 1G SFP RJ45 T Transceiver		JD089B
HPE X120 1G SFP LC BX 10-U Transceiver		JD098B
HPE X120 1G SFP LC BX 10-D Transceiver		JD099B
HPE X120 1G SFP LC LH100 Transceiver		JD103A
HPE X120 1G SFP LC LH40 1550nm Transceiver		JD062A
HPE X120 1G SFP LC SX Transceiver		JD118B
HPE X120 1G SFP LC LX Transceiver		JD119B
HPE X125 1G SFP LC LH40 1310nm Transceiver		JD061A
HPE X125 1G SFP LC LH70 Transceiver		JD063B
HPE X170 1G SFP LC LH70 1550 Transceiver		JD109A
HPE X170 1G SFP LC LH70 1570 Transceiver		JD110A
HPE X170 1G SFP LC LH70 1590 Transceiver		JD111A
HPE X170 1G SFP LC LH70 1610 Transceiver		JD112A
HPE X170 1G SFP LC LH70 1510 Transceiver		JD115A

SFP+ Transceivers

HPE X130 10G SFP+ LC SR Transceiver		JD092B
HPE X130 10G SFP+ LC LRM Transceiver		JD093B
HPE X130 10G SFP+ LC LR Transceiver		JD094B
HPE X130 10G SFP+ LC ER 40km Transceiver		JG234A
HPE FlexNetwork X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable		JD095C
HPE FlexNetwork X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable		JD096C
HPE FlexNetwork X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable		JD097C
HPE FlexNetwork X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable		JG081C
HPE FlexNetwork X240 10G SFP+ SFP+ 7m Direct Attach Copper Cable		JC784C

QSFP+ Transceivers

HPE X140 40G QSFP+ LC LR4 SM 10km 1310nm Transceiver		JG661A
HPE X140 40G QSFP+ MPO SR4 Transceiver		JG325B
HPE X140 40G QSFP+ MPO MM 850nm CSR4 300m Transceiver		JG709A
HPE FlexNetwork X240 40G QSFP+ QSFP+ 1m Direct Attach Copper Cable		JG326A
HPE FlexNetwork X240 40G QSFP+ QSFP+ 3m Direct Attach Copper Cable		JG327A
HPE FlexNetwork X240 40G QSFP+ QSFP+ 5m Direct Attach Copper Cable		JG328A
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 1m Direct Attach Copper Splitter Cable		JG329A
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 3m Direct Attach Copper Splitter Cable		JG330A
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 5m Direct Attach Copper Splitter Cable		JG331A

CFP Transceivers

HP X150 100G CFP LC LR4 10km SM Transceiver		JG829A

Switch Enclosure Options

Mounting Kit

HPE X421 Chassis Universal 4-post Rackmount Kit		JC665A
		See Configuration NOTE:1

Configuration Rules

Note 1	If any 11900 switch is installed into a rack, Then this Rack Mounting kit is required.

Remarks:	Default a quantity of 1 when Switch is selected.

Software Licenses

HP Unified Wired-WLAN 128 AP E-LTU		JG649AAE
(min 0 // max 7) REMARK: This license is for use with the Primary Controllers.		See Configuration NOTE:1

HP Unified Wired-WLAN 128 AP Redundant E-LTU		JG902AAE
(min 0 // max 7) REMARK: This license is for use with the Redundant Controllers.		See Configuration NOTE:1

Configuration Rules

Note 1	Only supported on JG639A and JG645A.

Remarks:	JG649AAE is optional to increase the AP by a count of 128 per E-LTU JG902AAE - Redundant access point licenses are intended for use only on a redundant controller module in a 1+1 or N+1 configuration or when extra access point capacity is required for failover in an N+N configuration.

Fans

HPE FlexFabric 11908 V Spare Fan Assembly		JG618A

Power Supply Cables

(std 0 // max 1) User Selection (min 1 // max 1) per DC Power Supply

HPE FlexNetwork 10500 48V 3m DC Power Supply Cable		JG390A
HPE FlexNetwork 10500 48V 15m DC Power Supply Cable		JG391A

Technical Specifications

HPE FlexFabric 11908 V Switch Chassis (JG608A)
I/O ports and slots	8 I/O module slots Supports a maximum of 384 1/10GbE ports or 192 1/10GBASE-T ports or 64 40GbE ports, or a combination
Additional ports and slots	2 MPU (for management modules) slots 4 switch fabric slots
Power supplies	6 power supply slots 1 minimum power supply required (ordered separately)
Fan tray	includes: 1 x JC634A 1 fan tray slot
Physical characteristics	Dimensions	17.32(w) x 25.98(d) x 34.88(h) in (43.99 x 65.99 x 88.6 cm) (20U height)
	Weight	169.53 lb (76.9 kg) chassis
	Full configuration weight	331.31 lb (150.28 kg)
Memory and processor	Management module	Dual Core MIPS64 @ 1.2 GHz, 512 MB flash, 8 GB DDR2 SDRAM
Mounting and enclosure	Mounts in an EIA-standard 19-inch rack or other equipment cabinet (hardware included); Horizontal surface mounting only
Performance	Throughput	up to 5.8 Bpps (64-byte packets)
	Switching capacity	7.7 Tbps
	Routing table size	16384 entries (IPv4), 8192 entries (IPv6)
	MAC address table size	131072 entries
Reliability	Availability	99.999%
Environment	Operating temperature	32°F to 113°F (0°C to 45°C)
	Operating relative humidity	10% to 95%, noncondensing
	Nonoperating/Storage temperature	-40°F to 158°F (-40°C to 70°C)
	Nonoperating/Storage relative humidity	5% to 95%, noncondensing
	Altitude	up to 13,123 ft (4 km)
	Acoustic	Low-speed fan: 61.6 dB, High-speed fan: 72.6 dB
Electrical characteristics	Voltage	100 - 120 / 200 - 240 VAC, rated -48 to -60 VDC, rated (depending on power supply chosen)
	Current	16/60 A
	Power output	2500 W
	Frequency	50/60 Hz
	Notes	Based on a common power supply of 2,500 W (AC)
Safety	CAN/CSA 22.2 No. 60950-1; FCC Part 15, Subpart B; FDA 21 CFR Subchapter J; ROHS Compliance; IEC 60950-1 :Second Edition ; EN 60950-1:2006 + A11:2009; AS/NZS 60950-1; IEC 60825-1; UL 60950-1, 2nd Edition; EN60825-2:2004+A1:2007
Emissions	VCCI Class A; EN 55022 Class A; CISPR 22 Class A; IEC/EN 61000-3-2; IEC/EN 61000-3-3; ICES-003 Class A; AS/NZS CISPR 22 Class A; FCC (CFR 47, Part 15) Class A; GB9254
Immunity	Generic	Directive 2004/108/EC
	EN	EN 55024:1998+ A1:2001 + A2:2003; ETSI EN 300 386 V1.3.3
	ESD	EN 61000-4-2
	Radiated	EN 61000-4-3
	EFT/Burst	EN 61000-4-4
	Surge	EN 61000-4-5
	Conducted	EN 61000-4-6
	Power frequency magnetic field	IEC 61000-4-8
	Voltage dips and interruptions	EN 61000-4-11
	Harmonics	EN 61000-3-2, IEC 61000-3-2
	Flicker	EN 61000-3-3, IEC 61000-3-3
Management	IMC - Intelligent Management Center; command-line interface; out-of-band management (serial RS-232C); SNMP Manager; Telnet; terminal interface (serial RS-232C); modem interface; IEEE 802.3 Ethernet MIB; Ethernet Interface MIB
Services	Refer to the Hewlett Packard Enterprise website at: http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

Standards and protocols
(applies to all products in series)

BGP
RFC 1771 BGPv4
RFC 1772 Application of the BGP
RFC 1997 BGP Communities Attribute
RFC 1998 PPP Gandalf FZA Compression Protocol
RFC 2385 BGP Session Protection via TCP MD5
RFC 2439 BGP Route Flap Damping
RFC 2796 BGP Route Reflection
RFC 2858 BGP-4 Multi-Protocol Extensions
RFC 2918 Route Refresh Capability
RFC 3065 Autonomous System Confederations for BGP
RFC 3392 Capabilities Advertisement with BGP-4
RFC 4271 A Border Gateway Protocol 4 (BGP-4)
RFC 4272 BGP Security Vulnerabilities Analysis
RFC 4273 Definitions of Managed Objects for BGP-4
RFC 4274 BGP-4 Protocol Analysis
RFC 4275 BGP-4 MIB Implementation Survey
RFC 4276 BGP-4 Implementation Report
RFC 4277 Experience with the BGP-4 Protocol
RFC 4360 BGP Extended Communities Attribute
RFC 4456 BGP Route Reflection: An Alternative to Full Mesh Internal BGP (IBGP)
RFC 5291 Outbound Route Filtering Capability for BGP-4
RFC 5292 Address-Prefix-Based Outbound Route Filter for BGP-4

Denial of service protection
Automatic filtering of well-known denial-of-service packets
CPU DoS Protection
Rate Limiting by ACLs

Device management
RFC 1157 SNMPv1/v2c
RFC 1305 NTPv3
RFC 1902 (SNMPv2)
RFC 2579 (SMIv2 Text Conventions)
RFC 2580 (SMIv2 Conformance)
RFC 2819 (RMON groups Alarm, Event, History and
Statistics only)
HTTP, SSHv1, and Telnet
Multiple Configuration Files
Multiple Software Images
SSHv1/SSHv2 Secure Shell
TACACS/TACACS+
Web UI

General protocols
IEEE 802.1ad Q-in-Q
IEEE 802.1ag Service Layer OAM
IEEE 802.1p Priority
IEEE 802.1Q VLANs
IEEE 802.1s Multiple Spanning Trees
IEEE 802.1w Rapid Reconfiguration of Spanning Tree
IEEE 802.1X PAE
IEEE 802.3ab 1000BASE-T
IEEE 802.3ac (VLAN Tagging Extension)
IEEE 802.3ad Link Aggregation Control Protocol (LACP)
IEEE 802.3ae 10-Gigabit Ethernet
IEEE 802.3ah Ethernet in First Mile over Point to Point Fiber - EFMF
IEEE 802.3ba 40 and 100 Gigabit Ethernet Architecture
IEEE 802.3x Flow Control
IEEE 802.3z 1000BASE-X
RFC 768 UDP
RFC 783 TFTP Protocol (revision 2)
RFC 791 IP
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 TELNET
RFC 894 IP over Ethernet
RFC 925 Multi-LAN Address Resolution
RFC 950 Internet Standard Subnetting Procedure
RFC 959 File Transfer Protocol (FTP)
RFC 1027 Proxy ARP
RFC 1035 Domain Implementation and Specification
RFC 1042 IP Datagrams
RFC 1058 RIPv1
RFC 1142 OSI IS-IS Intra-domain Routing Protocol
RFC 1195 OSI ISIS for IP and Dual Environments
RFC 1213 Management Information Base for Network
Management of TCP/IP-based internets
RFC 1293 Inverse Address Resolution Protocol
RFC 1305 NTPv3
RFC 1350 TFTP Protocol (revision 2)
RFC 1393 Traceroute Using an IP Option
RFC 1519 CIDR
RFC 1531 Dynamic Host Configuration Protocol
RFC 1533 DHCP Options and BOOTP Vendor Extensions
RFC 1591 DNS (client only)
RFC 1624 Incremental Internet Checksum
RFC 1701 Generic Routing Encapsulation
RFC 1721 RIP-2 Analysis
RFC 1723 RIP v2
RFC 1812 IPv4 Routing
RFC 2082 RIP-2 MD5 Authentication
RFC 2091 Trigger RIP
RFC 2131 DHCP
RFC 2138 Remote Authentication Dial In User Service (RADIUS)
RFC 2236 IGMP Snooping
RFC 2338 VRRP
RFC 2453 RIPv2
RFC 2644 Directed Broadcast Control
RFC 2763 Dynamic Name-to-System ID mapping support
RFC 2784 Generic Routing Encapsulation (GRE)
RFC 2865 Remote Authentication Dial In User Service (RADIUS)
RFC 2966 Domain-wide Prefix Distribution with
Two-Level IS-IS
RFC 2973 IS-IS Mesh Groups
RFC 3022 Traditional IP Network Address Translator (Traditional NAT)
RFC 3277 IS-IS Transient Blackhole Avoidance
RFC 3567 Intermediate System to Intermediate System (IS-IS) Cryptographic Authentication
RFC 3719 Recommendations for Interoperable Networks using Intermediate System to Intermediate System (IS-IS)
RFC 3784 ISIS TE support
RFC 3786 Extending the Number of IS-IS LSP Fragments
Beyond the 256 Limit
RFC 3787 Recommendations for Interoperable IP
Networks using Intermediate System to Intermediate System (IS-IS)
RFC 3847 Restart signaling for IS-IS
RFC 4251 The Secure Shell (SSH) Protocol Architecture
RFC 4486 Subcodes for BGP Cease Notification Message
RFC 4884 Extended ICMP to Support Multi-Part
Messages
RFC 4941 Privacy Extensions for Stateless Address
Autoconfiguration in IPv6
RFC 5130 A Policy Control Mechanism in IS-IS Using Administrative Tags

IP multicast
RFC 2236 IGMPv2
RFC 2283 Multiprotocol Extensions for BGP-4
RFC 2362 PIM Sparse Mode
RFC 3376 IGMPv3
RFC 3446 Anycast Rendezvous Point (RP) mechanism using Protocol Independent Multicast (PIM) and Multicast Source Discovery Protocol (MSDP)
RFC 3618 Multicast Source Discovery Protocol (MSDP)
RFC 3973 PIM Dense Mode
RFC 4541 Considerations for Internet Group
Management Protocol (IGMP) and Multicast Listener
Discovery (MLD) Snooping Switches
RFC 4601 PIM Sparse Mode
RFC 4604 Using Internet Group Management Protocol
Version 3 (IGMPv3) and Multicast Listener Discovery
Protocol Version 2 (MLDv2) for Source-Specific Multicast
RFC 4605 IGMP/MLD Proxying
RFC 4607 Source-Specific Multicast for IP
RFC 5059 Bootstrap Router (BSR) Mechanism for
Protocol Independent Multicast (PIM)

IPv6
RFC 1886 DNS Extension for IPv6
RFC 1887 IPv6 Unicast Address Allocation Architecture
RFC 1981 IPv6 Path MTU Discovery
RFC 2080 RIPng for IPv6
RFC 2081 RIPng Protocol Applicability Statement
RFC 2292 Advanced Sockets API for IPv6
RFC 2373 IPv6 Addressing Architecture
RFC 2375 IPv6 Multicast Address Assignments
RFC 2460 IPv6 Specification
RFC 2461 IPv6 Neighbor Discovery
RFC 2462 IPv6 Stateless Address Auto-configuration
RFC 2463 ICMPv6
RFC 2464 Transmission of IPv6 over Ethernet Networks
RFC 2473 Generic Packet Tunneling in IPv6
RFC 2526 Reserved IPv6 Subnet Anycast Addresses
RFC 2529 Transmission of IPv6 Packets over IPv4
RFC 2545 Use of MP-BGP-4 for IPv6
RFC 2553 Basic Socket Interface Extensions for IPv6
RFC 2710 Multicast Listener Discovery (MLD) for IPv6
RFC 2740 OSPFv3 for IPv6
RFC 2767 Dual stacks IPv46 & IPv6
RFC 2893 Transition Mechanisms for IPv6 Hosts and Routers
RFC 3056 Connection of IPv6 Domains via IPv4 Clouds
RFC 3307 IPv6 Multicast Address Allocation

RFC 3315 DHCPv6 (client and relay)
RFC 3484 Default Address Selection for IPv6
RFC 3513 IPv6 Addressing Architecture
RFC 3736 Stateless Dynamic Host Configuration
Protocol (DHCP) Service for IPv6
RFC 3810 MLDv2 for IPv6
RFC 4214 Intra-Site Automatic Tunnel Addressing
Protocol (ISATAP)
RFC 4861 IPv6 Neighbor Discovery
RFC 4862 IPv6 Stateless Address Auto-configuration

MIBs
RFC 1156 (TCP/IP MIB)
RFC 1157 A Simple Network Management Protocol
(SNMP)
RFC 1215 A Convention for Defining Traps for use with the SNMP
RFC 1229 Interface MIB Extensions
RFC 1493 Bridge MIB
RFC 1573 SNMP MIB II
RFC 1643 Ethernet MIB
RFC 1657 BGP-4 MIB
RFC 1724 RIPv2 MIB
RFC 1907 SNMPv2 MIB
RFC 2011 SNMPv2 MIB for IP
RFC 2012 SNMPv2 MIB for TCP
RFC 2013 SNMPv2 MIB for UDP
RFC 2096 IP Forwarding Table MIB
RFC 2233 Interface MIB
RFC 2452 IPV6-TCP-MIB
RFC 2454 IPV6-UDP-MIB
RFC 2465 IPv6 MIB
RFC 2466 ICMPv6 MIB
RFC 2571 SNMP Framework MIB
RFC 2572 SNMP-MPD MIB
RFC 2573 SNMP-Target MIB
RFC 2578 Structure of Management Information Version
2 (SMIv2)
RFC 2580 Conformance Statements for SMIv2
RFC 2618 RADIUS Client MIB
RFC 2620 RADIUS Accounting MIB
RFC 2665 Ethernet-Like-MIB
RFC 2668 802.3 MAU MIB
RFC 2674 802.1p and IEEE 802.1Q Bridge MIB
RFC 2787 VRRP MIB
RFC 2819 RMON MIB
RFC 2925 Ping MIB
RFC 2932IP (Multicast Routing MIB)
RFC 2933 IGMP MIB
RFC 2934 Protocol Independent Multicast MIB for IPv4
RFC 3414 SNMP-User based-SM MIB
RFC 3415 SNMP-View based-ACM MIB
RFC 3417 Simple Network Management Protocol (SNMP) over IEEE 802 Networks
RFC 3418 MIB for SNMPv3
RFC 3595 Textual Conventions for IPv6 Flow Label
RFC 3621 Power Ethernet MIB
RFC 3813 MPLS LSR MIB
RFC 3814 MPLS FTN MIB
RFC 3815 MPLS LDP MIB
RFC 3826 AES for SNMP's USM MIB
RFC 4133 Entity MIB (Version 3)
RFC 4444 Management Information Base for
Intermediate System to Intermediate System (IS-IS)

MPLS
RFC 2205 Resource ReSerVation Protocol
RFC 2209 Resource ReSerVation Protocol (RSVP)
RFC 2702 Requirements for Traffic Engineering Over MPLS
RFC 2858 Multiprotocol Extensions for BGP-4
RFC 2961 RSVP Refresh Overhead Reduction Extensions
RFC 3031 Multiprotocol Label Switching Architecture
RFC 3032 MPLS Label Stack Encoding
RFC 3107 Carrying Label Information in BGP-4
RFC 3212 Constraint-Based LSP Setup using LDP
RFC 3479 Fault Tolerance for the Label Distribution
Protocol (LDP)
RFC 3487 Graceful Restart Mechanism for LDP
RFC 3564 Requirements for Support of Differentiated
Service-aware MPLS Traffic Engineering
RFC 4364 BGP/MPLS IP Virtual Private Networks (VPNs)
RFC 4379 Detecting Multi-Protocol Label Switched
(MPLS) Data Plane Failures
RFC 4447 Pseudowire Setup and Maintenance Using LDP
RFC 4448 Encapsulation Methods for Transport of
Ethernet over MPLS Networks
RFC 4664 Framework for Layer 2 Virtual Private
Networks
RFC 4665 Service Requirements for Layer 2 Provider
Provisioned Virtual Private Networks
RFC 4761 Virtual Private LAN Service (VPLS) Using BGP for Auto-Discovery and Signaling
RFC 4762 Virtual Private LAN Service (VPLS) Using Label
Distribution Protocol (LDP) Signaling
RFC 5036 LDP Specification

Network management
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
RFC 1155 Structure of Management Information
RFC 1157 SNMPv1
RFC 1448 Protocol Operations for version 2 of the
Simple Network Management Protocol (SNMPv2)
RFC 2211 Controlled-Load Network
RFC 2819 Four groups of RMON: 1 (statistics), 2 (history), 3 (alarm) and 9 (events)
RFC 3176 sFlow
RFC 3411 SNMP Management Frameworks
RFC 3412 SNMPv3 Message Processing
RFC 3414 SNMPv3 User-based Security Model (USM)
RFC 3415 SNMPv3 View-based Access Control Model VACM)
ANSI/TIA-1057 LLDP Media Endpoint Discovery
(LLDP-MED)

OSPF
RFC 1245 OSPF protocol analysis
RFC 1246 Experience with OSPF
RFC 1765 OSPF Database Overflow
RFC 1850 OSPFv2 Management Information Base (MIB), traps
RFC 2154 OSPF w/ Digital Signatures (Password, MD-5)
RFC 2328 OSPFv2
RFC 2370 OSPF Opaque LSA Option
RFC 3101 OSPF NSSA
RFC 3137 OSPF Stub Router Advertisement
RFC 3623 Graceful OSPF Restart
RFC 3630 Traffic Engineering Extensions to OSPFv2
RFC 4061 Benchmarking Basic OSPF Single Router
Control Plane Convergence
RFC 4062 OSPF Benchmarking Terminology and
Concepts
RFC 4063 Considerations When Using Basic OSPF
Convergence Benchmarks
RFC 4222 Prioritized Treatment of Specific OSPF Version
2 Packets and Congestion Avoidance
RFC 4577 OSPF as the Provider/Customer Edge Protocol for BGP/MPLS IP Virtual Private Networks (VPNs)
RFC 4811 OSPF Out-of-Band LSDB Resynchronization
RFC 4812 OSPF Restart Signaling
RFC 4813 OSPF Link-Local Signaling
RFC 4940 IANA Considerations for OSPF

QoS/CoS
IEEE 802.1P (CoS)
RFC 1349 Type of Service in the Internet Protocol Suite
RFC 2211 Specification of the Controlled-Load Network
Element Service
RFC 2212 Guaranteed Quality of Service
RFC 2474 DSCP DiffServ
RFC 2475 DiffServ Architecture
RFC 2597 DiffServ Assured Forwarding (AF)
RFC 2598 DiffServ Expedited Forwarding (EF)

Security
IEEE 802.1X Port Based Network Access Control
RFC 1321 The MD5 Message-Digest Algorithm
RFC 1334 PPP Authentication Protocols (PAP)
RFC 1492 TACACS+
RFC 1994 PPP Challenge Handshake Authentication
Protocol (CHAP)
RFC 2082 RIP-2 MD5 Authentication
RFC 2104 Keyed-Hashing for Message Authentication
RFC 2408 Internet Security Association and Key
Management Protocol (ISAKMP)
RFC 2409 The Internet Key Exchange (IKE)
RFC 2716 PPP EAP TLS Authentication Protocol
RFC 2865 RADIUS Authentication
RFC 2866 RADIUS Accounting
RFC 2868 RADIUS Attributes for Tunnel Protocol Support
RFC 2869 RADIUS Extensions
Access Control Lists (ACLs)
Guest VLAN for 802.1x
MAC Authentication
Port Security
SSHv1/SSHv2 Secure Shell

VPN
RFC 2403 - HMAC-MD5-96
RFC 2404 - HMAC-SHA1-96
RFC 2405 - DES-CBC Cipher algorithm
RFC 2407 - Domain of interpretation
RFC 2547 BGP/MPLS VPNs
RFC 2917 A Core MPLS IP VPN Architecture
RFC 4302 - IP Authentication Header (AH)
RFC 4303 - IP Encapsulating Security Payload (ESP)

Accessories

HPE FlexFabric 11900 Switch Series accessories
Modules
HPE FlexFabric 11900 48-port 10GbE SFP+ SF Module	JG612A
HPE FlexFabric 11900 32-port 10GbE SFP+ SF Module	JG611A
HPE FlexFabric 11900 Main Processing Unit	JG609A
HPE FlexFabric 11900 24-port 1/10GBASE-T SF Module	JG615A
HPE FlexFabric 11900 4-port 40GbE QSFP+ SF Module	JG613A
HPE FlexFabric 11900 8-port 40GbE QSFP+ SF Module	JG614A
HPE FlexFabric 11900 2-port 100GbE CFP SE Module	JG918A

Transceivers
HPE X120 1G SFP RJ45 T Transceiver	JD089B
HPE X120 1G SFP LC SX Transceiver	JD118B
HPE X120 1G SFP LC LX Transceiver	JD119B
HPE X125 1G SFP LC LH40 1310nm Transceiver	JD061A
HPE X120 1G SFP LC LH40 1550nm Transceiver	JD062A
HPE X125 1G SFP LC LH70 Transceiver	JD063B
HPE X120 1G SFP LC LH100 Transceiver	JD103A
HPE X120 1G SFP LC BX 10-D Transceiver	JD099B
HPE X120 1G SFP LC BX 10-U Transceiver	JD098B
HPE X170 1G SFP LC LH70 1510 Transceiver	JD115A
HPE X170 1G SFP LC LH70 1550 Transceiver	JD109A
HPE X170 1G SFP LC LH70 1570 Transceiver	JD110A
HPE X170 1G SFP LC LH70 1590 Transceiver	JD111A
HPE X170 1G SFP LC LH70 1610 Transceiver	JD112A
HPE X130 10G SFP+ LC SR Transceiver	JD092B
HPE X130 10G SFP+ LC LRM Transceiver	JD093B
HPE X130 10G SFP+ LC LR Transceiver	JD094B
HPE X130 10G SFP+ LC ER 40km Transceiver	JG234A
HPE FlexNetwork X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable	JD095C
HPE FlexNetwork X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable	JD096C
HPE FlexNetwork X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable	JD097C
HPE FlexNetwork X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable	JG081C
HPE FlexNetwork X240 10G SFP+ SFP+ 7m Direct Attach Copper Cable	JC784C
HPE FlexNetwork X240 40G QSFP+ QSFP+ 1m Direct Attach Copper Cable	JG326A
HPE FlexNetwork X240 40G QSFP+ QSFP+ 3m Direct Attach Copper Cable	JG327A
HPE FlexNetwork X240 40G QSFP+ QSFP+ 5m Direct Attach Copper Cable	JG328A
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 1m Direct Attach Copper Splitter Cable	JG329A
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 3m Direct Attach Copper Splitter Cable	JG330A
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 5m Direct Attach Copper Splitter Cable	JG331A
HPE X140 40G QSFP+ MPO SR4 Transceiver	JG325B
HPE X140 40G QSFP+ MPO MM 850nm CSR4 300m Transceiver	JG709A
HP X150 100G CFP LC LR4 10km SM Transceiver	JG829A

Power Supply
HPE FlexFabric 11900 2500W AC Power Supply	JG616A
HPE FlexFabric 11900 2400W DC Power Supply	JG617A

Mounting Kit
HPE X421 Chassis Universal 4-post Rackmount Kit	JC665A

Power cords
HPE FlexNetwork 10500 48V 3m DC Power Supply Cable	JG390A
HPE FlexNetwork 10500 48V 15m DC Power Supply Cable	JG391A

Appliance
HPE 10500/11900/7500 20Gbps VPN Firewall Module	JG372A

HPE FlexFabric 11908 V Switch Chassis (JG608A)
HPE FlexFabric 11908 1.92Tbps Type D Fabric Module	JG610A
HPE FlexFabric 11908 V Spare Fan Assembly	JG618A

Accessory Product Details

NOTE: Details are not available for all accessories. The following specifications were available at the time of publication.

Modules

HPE FlexFabric 11900 Main Processing Unit (JG609A)	Physical characteristics	Dimensions	15.71(w) x 13.86(d) x 1.57(h) in (39.9 x 35.2 x 3.99 cm)
	Physical characteristics	Weight	6.55 lb (2.97 kg)
	Services	Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HPE FlexFabric 11900 32-port 10GbE SFP+ SF Module (JG611A)	Ports	32 SFP+ 1/10GbE ports
	Physical characteristics	Dimensions	15.71(w) x 13.86(d) x 1.57(h) in (39.9 x 35.2 x 3.99 cm)
		Weight	7.61 lb (3.45 kg)
	Services	Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HPE FlexFabric 11900 48-port 10GbE SFP+ SF Module (JG612A)	Ports	48 SFP+ 1/10GbE ports
	Physical characteristics	Dimensions	15.71(w) x 13.86(d) x 1.57(h) in (39.9 x 35.2 x 3.99 cm)
		Weight	9.1 lb (4.13 kg)
	Services	Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HPE FlexFabric 11900 4-port 40GbE QSFP+ SF Module (JG613A)	Ports	4 QSFP+ 40-GbE ports
	Physical characteristics	Dimensions	15.71(w) x 13.86(d) x 1.57(h) in (39.9 x 35.2 x 3.99 cm)
		Weight	6.92 lb (3.14 kg)
	Services	Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HPE FlexFabric 11900 8-port 40GbE QSFP+ SF Module (JG614A)	Ports	8 QSFP+ 40-GbE ports
	Physical characteristics	Dimensions	15.71(w) x 13.86(d) x 1.57(h) in (39.9 x 35.2 x 3.99 cm)
		Weight	7.43 lb (3.37 kg)
	Services	Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

Transceivers

HPE X125 1G SFP LC LH40 1310nm Transceiver (JD061A) A small form-factor pluggable SFP Gigabit LH40 transceiver that provides a full duplex Gigabit solution up to 40km on a single-mode fiber.	Ports	1 LC 1000Base-LH port (no IEEE standard exists for 1550 nm optics)
	Connectivity	Connector type	LC
		Wavelength	1310 nm
	Physical characteristics	Dimensions	2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17 cm)
		Full configuration weight	0.04 lb. (0.02 kg)
	Electrical characteristics	Power consumption typical	0.8 W
		Power consumption maximum	1.0 W
	Cabling	Cable type: Single-mode fiber optic, complying with ITU-T G.652; Maximum distance: 40km distance
		Fiber type	Single Mode
	Services	Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HPE X120 1G SFP LC LH40 1550nm Transceiver (JD062A) A small form-factor pluggable (SFP) Gigabit LH40 transceiver that provides a full-duplex Gigabit solution up to 40 km on a single mode fiber.	Ports	1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics)
	Connectivity	Connector type	LC
		Wavelength	1550 nm
	Physical characteristics	Dimensions	2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17 cm)
		Full configuration weight	0.04 lb. (0.02 kg)
	Electrical characteristics	Power consumption typical	0.8 W
		Power consumption maximum	1.0 W
	Cabling	Cable type: Single-mode fiber optic, complying with ITU-T G.652; Maximum distance: 40km distance
		Fiber type	Single Mode
	Services	Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HPE X125 1G SFP LC LH70 Transceiver (JD063B) A small form-factor pluggable (SFP) Gigabit LH70 transceiver that provides a full-duplex Gigabit solution up to 70km on a single-mode fiber.	Ports	1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics)
	Connectivity	Connector type	LC
		Wavelength	1550 nm
	Physical characteristics	Dimensions	2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17 cm)
		Full configuration weight	0.04 lb. (0.02 kg)
	Electrical characteristics	Power consumption typical	0.8 W
		Power consumption maximum	1.0 W
	Cabling	Cable type: Single-mode fiber optic, complying with ITU-T G.652; Maximum distance: 70km
		Fiber type	Single Mode
	Services	Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HPE X120 1G SFP RJ45 T Transceiver (JD089B) A small form factor pluggable (SFP) Gigabit 1000Base-T transceiver that provides a full duplex Gigabit solution up to 100m on a Cat-5+ cable.	Ports	1 RJ-45 1000BASE-T port (IEEE 802.3ab Type 1000BASE-T)
	Connectivity	Connector type	RJ-45
	Physical characteristics	Dimensions	2.71(d) x 0.54(w) x 0.55(h) in. (6.88 x 1.37 x 1.4 cm)
		Full configuration weight	0.07 lb. (0.03 kg)
	Electrical characteristics	Power consumption typical	0.8 W
		Power consumption maximum	1.0 W
	Cabling	Cable type: 1000BASE-T: Category 5 (5E or better recommended), 100 Ù differential 4-pair unshielded twisted pair (UTP) or shielded twisted pair (STP) balanced, complying with IEEE 802.3ab 1000BASE-T; Maximum distance: 100m
	Services	Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HPE X120 1G SFP LC BX 10-U Transceiver (JD098B) A small form-factor pluggable (SFP) Gigabit LX-BX10-U transceiver that provides a full duplex Gigabit solution up to 10km on a single mode cable.	Ports	1 LC 1000BASE-BX10 port (IEEE 802.3ah Type 1000BASE-BX10-U); Duplex: full only
	Connectivity	Connector type	LC
	Physical characteristics	Dimensions	2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17 cm)
		Full configuration weight	0.04 lb. (0.02 kg)
	Electrical characteristics	Power consumption typical	0.8 W
		Power consumption maximum	1.0 W
	Cabling	Maximum distance: 10km
		Fiber type	Single Mode
	Notes	TX 1310nm RX 1490nm
	Services	Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HPE X120 1G SFP LC BX 10-D Transceiver (JD099B) A small form-factor pluggable (SFP) Gigabit LX-BX10-D transceiver that provides a full duplex Gigabit solution up to 10km on a single mode cable.	Ports	1 LC 1000BASE-BX10 port (IEEE 802.3ah Type 1000BASE-BX10-D); Duplex: full only
	Connectivity	Connector type	LC
	Physical characteristics	Dimensions	2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17 cm)
		Full configuration weight	0.04 lb. (0.02 kg)
	Electrical characteristics	Power consumption typical	0.8 W
		Power consumption maximum	1.0 W
	Cabling	Maximum distance: Up to 10km
		Fiber type	Single Mode
	Notes	TX 1490nm RX 1310nm
	Services	Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HPE X120 1G SFP LC LH100 Transceiver (JD103A) A small form factor pluggable (SFP) Gigabit LH100 transceiver that provides a full-duplex Gigabit solution up to 100km on a single mode fiber.	Ports	1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics)
	Connectivity	Connector type	LC
		Wavelength	1550 nm
	Electrical characteristics	Power consumption typical	0.8 W
		Power consumption maximum	1.0 W
	Cabling	Cable type: Single-mode fiber optic, complying with ITU-T G.652; Maximum distance: Up to 100km
		Fiber type	Single Mode
	Services	Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HPE X120 1G SFP LC SX Transceiver (JD118B) A small form-factor pluggable (SFP) Gigabit SX transceiver that provides a full-duplex Gigabit solution up to 550m on a Multimode fiber.	Ports	1 LC 1000BASE-SX port
	Connectivity	Connector type	LC
		Wavelength	850 nm
	Physical characteristics	Dimensions	2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17 cm)
		Full configuration weight	0.04 lb. (0.02 kg)
	Electrical characteristics	Power consumption typical	0.8 W
		Power consumption maximum	1.0 W
	Cabling	Maximum distance: FDDI Grade distance = 220m OM1 = 275m OM2 = 500m OM3 = Not Specified by standard
		Cable length	up to 550m
		Fiber type	Multi Mode
	Services	Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HPE X120 1G SFP LC LX Transceiver (JD119B) A small form-factor pluggable (SFP) Gigabig LX transceiver that provides a full duplex Gigabit solution up to 550m on MMF or 10Km on SMF	Ports	1 SFP 1000BASE-LX port (IEEE 802.3z Type 1000BASE-LX)
	Connectivity	Connector type	LC
		Wavelength	1300 nm
	Physical characteristics	Dimensions	2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17 cm)
		Full configuration weight	0.04 lb. (0.02 kg)
	Electrical characteristics	Power consumption typical	0.8 W
		Power consumption maximum	1.0 W
	Cabling	Cable type: Either single mode or multimode; Maximum distance: 550m for Multimode 10km for Singlemode
		Fiber type	Both
	Services	Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

Power Supplies

HPE FlexFabric 11900 2500W AC Power Supply (JG616A)	Physical characteristics	Dimensions	1.61(w) x 16.14(d) x 4.02(h) in (4.1 x 41.0 x 10.21 cm)
		Weight	9.26 lb (4.2 kg)
	Services	Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HPE FlexFabric 11900 2400W DC Power Supply (JG617A)	Physical characteristics	Dimensions	1.61(w) x 16.14(d) x 4.02(h) in (4.1 x 41.0 x 10.2 cm)
		Weight	5.29 lb (2.4 kg)
	Services	Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HPE FlexFabric 11908 V Switch Chassis (JG608A)

HPE FlexFabric 11908 1.92Tbps Type D Fabric Module (JG610A)	Physical characteristics	Dimensions	16.77(w) x 11.73(d) x 1.57(h) in (42.6 x 29.79 x 3.99 cm)
		Weight	9.7 lb (4.4 kg)
	Services	Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HPE FlexFabric 11908 V Spare Fan Assembly (JG618A)	Physical characteristics	Dimensions	17.32(w) x 25.75(d) x 3.15(h) in (43.99 x 65.41 x 8.0 cm)
		Weight	8.29 lb (3.76 kg)
	Services	Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

Summary of Changes

Date	Version History	Action	Description of Change
22-Apr-2016	From Version 11 to 12	Changed	SKU descriptions updated on the document
25-Mar-2016	From Version 10 to 11	Changed	Changes made on Product overview, Features and benefits and Technical Specifications
12-Dec-2014	From Version 9 to 10	Removed	Deleted SKU JG325A
18-Aug-2014	From Version 8 to 9	Added	New accessory: JG918A
18-Aug-2014	From Version 8 to 9	Changed	Product overview updated Configuration menu updated Technical Specifications updated
02-Jul-2014	From Version 7 to 8	Changed	Minor change on Overview section.
10-Jun-2014	From Version 6 to 7	Added	Added a new accessory: JG372A
31-Mar-2014	From Version 4 to 6	Changed	Transceivers were revised.
14-Oct-2014	From Version 3 to 4	Added	Added a new Transceiver in two locations in the Configuration section.
30-Sept-2014	From Version 2 to 3	Added	HP 10500/11900/7500 20Gbps VPN FW Mod was added to Modules.
12-Jul-2014	From Version 1 to 2	Changed	Made minor changes to the Configuration section.


Sign up for updates
	Rate this document

© Copyright 2016 Hewlett Packard Enterprise Development LP. The information contained herein is subject to change without notice. The only warranties for Hewlett Packard Enterprise products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. Hewlett Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.

To learn more, visit: http://www.hpe.com/networking

c04111418 - 14585 - Worldwide - V12 - 22- April-2016