HPE 5120 EI Switch Series: технические характеристики и документация

HPE 5120 EI Switch Series

HP 5120-48G EI Switch with 2 Interface Slots

HP 5120-48G EI Switch

HP 5120-24G EI Switch with 2 Interface Slots

HP 5120-24G EI Switch

HP 5120-48G-PoE+ EI Switch with 2 Interface Slots

HP 5120-24G-PoE+ EI Switch with 2 Interface Slots

Models

HP 5120-48G EI Switch with 2 Interface Slots

JE069A

HP 5120-48G EI Switch

JE067A

HP 5120-24G EI Switch with 2 Interface Slots

JE068A

HP 5120-24G EI Switch

JE066A

HP 5120-48G-PoE+ EI Switch with 2 Interface Slots

JG237A

HP 5120-24G-PoE+ EI Switch with 2 Interface Slots

JG236A

Key features

• High scalability for investment protection
• Support for multiple services
• Comprehensive security control policies
• Diversified Quality of Service (QoS) policies
• Excellent manageability

Product overview

The HPE 5120 EI Switch Series is comprised of Gigabit Ethernet switches that support static Layer 3 routing, diversified services, and IPv6 forwarding, as well as provide up to four 10GbE Ethernet extended interfaces. Unique Intelligent Resilient Fabric (IRF) technology creates a virtual fabric by managing several switches as one logical device, which increases network resilience, performance, and availability, while reducing operational complexity. These switches provide Gigabit Ethernet access and can be used at the edge of a network or to connect server clusters in data centers. High scalability provides investment protection with two expansion slots, each of which can support two 10GbE expansion modules. High availability, simplified management, and comprehensive security control policies are among the key features that distinguish this series.

Features and benefits

Quality of Service (QoS)

• Broadcast control
  allows limitation of broadcast traffic rate to cut down on unwanted network broadcast traffic
• Advanced classifier-based QoS
  classifies traffic using multiple match criteria based on Layer 2, 3, and 4 information; applies QoS policies such as setting priority level and rate limit to selected traffic on a port, VLAN, or whole switch
• Powerful QoS feature
  supports the following congestion actions: strict priority (SP) queuing, weighted round robin (WRR), and SP+WRR
• Traffic policing
  supports Committed Access Rate (CAR) and line rate

Management

• Friendly port names
  allows assignment of descriptive names to ports
• Remote configuration and management
  enables configuration and management through a secure Web browser or a CLI located on a remote device
• Manager and operator privilege levels
  provides read-only (operator) and read/write (manager) access on CLI and Web browser management interfaces
• Command authorization
  leverages HWTACACS to link a custom list of CLI commands to an individual network administrator's login; also provides an audit trail
• Secure Web GUI
  provides a secure, easy-to-use graphical interface for configuring
  the module via HTTPS
• Multiple configuration files
  stores easily to the flash image
• Complete session logging
  provides detailed information for problem identification and resolution
• SNMPv1, v2c, and v3
  facilitate centralized discovery, monitoring, and secure management of networking devices
• Remote monitoring (RMON)
  uses standard SNMP to monitor essential network functions; supports events, alarm, history, and statistics group plus a private alarm extension group
• IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
  advertises and receives management information from adjacent devices on a network, facilitating easy mapping by network
  management applications
• sFlow (RFC 3176)
  provides scalable ASIC-based wirespeed network monitoring and accounting with no impact on network performance; this allows network operators to gather a variety of sophisticated network statistics and information for capacity planning and real-time network monitoring purposes
• Management VLAN
  segments traffic to and from management interfaces, including CLI/Telnet, a Web browser interface, and SNMP
• Remote intelligent mirroring
  mirrors ingress/egress ACL-selected traffic from a switch port or VLAN to a local or remote switch port anywhere on the network
• Device Link Detection Protocol (DLDP)
  monitors a cable between two switches and shuts down the ports on both ends if the cable is broken, which prevents network problems such as loops
• IPv6 management
  provides future-proof networking because the switch is capable of being managed whether the attached network is running IPv4 or IPv6; supports pingv6, tracertv6, Telnetv6, TFTPv6, DNSv6, syslogv6, FTPv6, SNMPv6, DHCPv6, and RADIUS for IPv6
• Troubleshooting
  ingress and egress port monitoring enables network problem-solving; virtual cable tests provide visibility into cable problems

Connectivity

• Auto-MDIX
  automatically adjusts for straight-through or crossover cables on all 10/100/1000 ports
• Flow control
  provides back pressure using standard IEEE 802.3x, reducing congestion in heavy traffic situations
• Jumbo packet support
  supports up to 9216-byte frame size to improve the performance of large data transfers
• High-density connectivity
  provides up to 48 fixed 10/100/1000BASE-T ports in a Layer 2/Layer 3 switch
• Optional 10GbE ports
  deliver, through the use of optional modules, additional 10GbE connections, which are available for uplinks or high-bandwidth server connections; flexibly support copper, XFP, SFP+, or CX4 local connections
• IEEE 802.3at Power over Ethernet (PoE+) support
  simplifies deployment and dramatically reduces installation costs by helping to eliminate the time and cost involved in supplying local power at each access point locatio
• Ethernet operations, administration and maintenance (OAM)
  detects data link layer problems that occurred in the "last mile" using the IEEE 802.3ah OAM standard; monitors the status of the link between two devices
• High-bandwidth CX4 local stacking
  achieves 12 Gb/s per connection when using local CX4 stacking, allowing for up to 96 Gb/s total stacking bandwidth (full duplex) in a resilient stacking configuration

Performance

• Nonblocking architecture
  up to 192 Gb/s nonblocking switching fabric provides wirespeed switching with up to 143 million pps throughput
• Hardware-based wirespeed access control lists (ACLs)
  help provide high levels of security and ease of administration without impacting network performance with a feature-rich TCAM-based ACL implementation

Resiliency and high availability

• Separate data and control paths
  separates control from services and keeps service processing isolated; increases security and performance
• External redundant power supply
  provides high reliability
• Smart link
  allows 50 ms failover between links
• Spanning Tree/MSTP, RSTP
  provides redundant links while preventing network loops
• Rapid Ring Protection Protocol (RRPP)
  connects multiple switches in a high-performance ring using standard Ethernet technology; traffic can be rerouted around the ring in less than 50 ms, reducing the impact on traffic and applications
• Intelligent Resilient Fabric (IRF)
  creates virtual resilient switching fabrics, where two or more switches perform as a single L2 switch and L3 router; switches do not have to be co-located and can be part of a disaster-recovery system; servers or switches can be attached using standard LACP for automatic load balancing and high availability; can eliminate the need for complex protocols like Spanning Tree Protocol, Equal-Cost Multipath (ECMP), or VRRP, thereby simplifying network operation

Layer 2 switching

• 16K MAC address table
  provides access to many Layer 2 devices
• VLAN support and tagging
  supports IEEE 802.1Q with 4,094 simultaneous VLAN IDs
• GARP VLAN Registration Protocol
  allows automatic learning and dynamic assignment of VLANs
• IEEE 802.1ad QinQ and selective QinQ
  increase the scalability of an Ethernet network by providing a hierarchical structure; connect multiple LANs on a high-speed
  campus or metro network
• 10GbE port aggregation
  allows grouping of ports to increase overall data throughput to a remote device
• Internet Group Management Protocol (IGMP) and Multicast
  Listener Discovery (MLD) protocol snooping
  controls and manages the flooding of multicast packets in a Layer 2 network
• Per-VLAN Spanning Tree Plus (PVST+)
  allows each VLAN to build a separate spanning tree to improve link bandwidth usage in network environments with multiple VLANs

Layer 3 services

• Address Resolution Protocol (ARP)
  determines the MAC address of another IP host in the same subnet; supports static ARPs; gratuitous ARP allows detection of duplicate IP addresses; proxy ARP allows normal ARP operation between subnets or when subnets are separated by a Layer 2 network
• Dynamic Host Configuration Protocol (DHCP)
  simplifies the management of large IP networks; supports client; DHCP Relay enables DHCP operation across subnets
• Loopback interface address
  defines an address that can always be reachable, improving diagnostic capability
• User Datagram Protocol (UDP) helper function
  allows UDP broadcasts to be directed across router interfaces to specific IP unicast or subnet broadcast addresses and prevents server spoofing for UDP services such as DHCP
• Route maps
  provide more control during route redistribution; allow filtering and altering of route metrics

Layer 3 routing

• Static IP routing
  provides manually configured routing for both IPv4 and IPv6 networks

Security

• Access control lists (ACLs)
  provides IP Layer 2 to Layer 4 traffic filtering; supports global ACL, VLAN ACL, port ACL, and IPv6 ACL
• IEEE 802.1X
  industry-standard method of user authentication using an IEEE 802.1X supplicant on the client in conjunction with a RADIUS erver
• MAC-based authentication
  client is authenticated with the RADIUS server based on the client's MAC address
• Identity-driven security and access control
• Per-user ACLs
  permits or denies user access to specific network resources based on user identity and time of day, allowing multiple types of users on the same network to access specific network services without risking network security or providing unauthorized access to sensitive data
• Automatic VLAN assignment
  automatically assigns users to the appropriate VLAN based on their identities
• Secure management access
  delivers secure encryption of all access methods (CLI, GUI, or MIB) through SSHv2, SSL, and/or SNMPv3
• Secure FTP
  allows secure file transfer to and from the switch; protects against unwanted file downloads or unauthorized copying of a switch configuration file
• Guest VLAN
  provides a browser-based environment to authenticated clients that is similar to IEEE 802.1X
• Endpoint Admission Defense (EAD)
  provides security policies to users accessing a network
• Port security
  allows access only to specified MAC addresses, which can be learned or specified by the administrator
• Port isolation
  secures and adds privacy, and prevents malicious attackers from obtaining user information
• STP BPDU port protection
  blocks Bridge Protocol Data Units (BPDUs) on ports that do not require BPDUs, preventing forged BPDU attacks
• STP root guard
  protects the root bridge from malicious attacks or configuration mistakes
• DHCP protection
  blocks DHCP packets from unauthorized DHCP servers, preventing denial-of-service attacks
• IP source guard
  helps prevent IP spoofing attacks
• Dynamic ARP protection
  blocks ARP broadcasts from unauthorized hosts, preventing eavesdropping or theft of network data
• RADIUS/HWTACACS
  eases switch management security administration by using a password authentication server

Convergence

• IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
  facilitates easy mapping using network management applications with LLDP automated device discovery protocol
• LLDP-MED
  is a standard extension that automatically configures network devices, including LLDP-capable IP phones
• LLDP-CDP compatibility
  receives and recognizes CDP packets from Cisco's IP phones for seamless interoperation
• IEEE 802.3af Power over Ethernet
  provides up to 15.4 W per port to PoE-powered devices such as IP phones, wireless access points, and video cameras
• PoE allocations
  supports multiple methods (automatic, IEEE 802.3af class, LLDP-MED, or user-specified) to allocate PoE power for more efficient energy savings
• Voice VLAN
  automatically assigns VLAN and priority for IP phones, simplifying network configuration and maintenance
• IP multicast snooping (data-driven IGMP)
  prevents flooding of IP multicast traffic

Device support

• Cisco prestandard PoE support
  detects and provides power to Cisco's prestandard PoE devices such as wireless LAN access points and IP phones

Additional information

• Green IT and power
  improves energy efficiency through the use of the latest advances in silicon development; shuts off unused ports and utilizes
  variable-speed fans, reducing energy costs
• Green initiative support
  provides support for RoHS and WEEE regulations

Warranty and support

• · Limited Lifetime Warranty
  See http://www.hpe.com/networking/warrantysummary for warranty and support information included with your product purchase.
• · Software releases
  to find software for your product, refer to http://www.hpe.com/networking/support; for details on the software releases available with your product purchase, refer to http://www.hpe.com/networking/warrantysummary

Build To Order:
BTO is a standalone unit with no integration. BTO products ship standalone are not part of a CTO or Rack-Shippable solution.

Standard Switch Chassis

HP 5120-24G EI Switch

JE066A

• 24 RJ-45 autosensing 10/100/1000 ports
• 4 dual-personality ports; PoE auto-sensing 10/100/1000Base-T or SFP
• min=0 \ max=4 SFP Transceivers
• 0 port expansion module slots
• Power supply included
• 1U - Height

See Configuration NOTE: 1, 3

PDU Cable NA/MEX/TW/JP

JE066A#B2B

• C15 PDU Jumper Cord (NA/MEX/TW/JP)

PDU Cable ROW

JE066A#B2C

• C15 PDU Jumper Cord (ROW)

HP 5120-24G EI Switch with 2 Slots

JE068A

• 24 RJ-45 autosensing 10/100/1000 ports
• 4 dual-personality ports; PoE auto-sensing 10/100/1000Base-T or SFP
• min=0 \ max=4 SFP Transceivers
• 2 port expansion module slots
• Power supply included
• 1U - Height

See Configuration NOTE: 1, 3

PDU Cable NA/MEX/TW/JP

JE068A#B2B

• C15 PDU Jumper Cord (NA/MEX/TW/JP)

PDU Cable ROW

JE068A#B2C

• C15 PDU Jumper Cord (ROW)

HP 5120-24G-PoE+ EI Switch w/2 Intf Slts

JG236A

• 24 RJ-45 autosensing 10/100/1000 ports
• 4 dual-personality ports; PoE auto-sensing 10/100/1000Base-T or SFP
• min=0 \ max=4 SFP Transceivers
• 2 port expansion module slots
• Power supply included
• 1U - Height

See Configuration NOTE: 1, 3

PDU Cable NA/MEX/TW/JP

JG236A#B2B

• C15 PDU Jumper Cord (NA/MEX/TW/JP)

PDU Cable ROW

JG236A#B2C

• C15 PDU Jumper Cord (ROW)

HP 5120-48G EI Switch

JE067A

• 48 RJ-45 autosensing 10/100/1000 ports
• 4 dual-personality ports; PoE auto-sensing 10/100/1000Base-T or SFP
• min=0 \ max=4 SFP Transceivers
• 0 port expansion module slots
• Power supply included
• 1U - Height

See Configuration NOTE: 1, 3

PDU Cable NA/MEX/TW/JP

JE067A#B2B

• C15 PDU Jumper Cord (NA/MEX/TW/JP)

PDU Cable ROW

JE067A#B2C

• C15 PDU Jumper Cord (ROW)

HP 5120-48G EI Switch with 2 Slots

JE069A

• 48 RJ-45 autosensing 10/100/1000 ports
• 4 dual-personality ports; PoE auto-sensing 10/100/1000Base-T or SFP
• min=0 \ max=4 SFP Transceivers
• 2 port expansion module slots
• Power supply included
• 1U - Height

See Configuration NOTE: 1, 3

PDU Cable NA/MEX/TW/JP

JE069A#B2B

• C15 PDU Jumper Cord (NA/MEX/TW/JP)

PDU Cable ROW

JE069A#B2C

• C15 PDU Jumper Cord (ROW)

HP 5120-48G-PoE+ EI Switch w/2 Intf Slts

JG237A

• 48 RJ-45 autosensing 10/100/1000 ports
• 4 dual-personality ports; PoE auto-sensing 10/100/1000Base-T or SFP
• min=0 \ max=4 SFP Transceivers
• 2 port expansion module slots
• Power supply included
• 1U - Height

See Configuration NOTE: 1, 3

PDU Cable NA/MEX/TW/JP

JG237A#B2B

• C15 PDU Jumper Cord (NA/MEX/TW/JP)

PDU Cable ROW

JG237A#B2C

• C15 PDU Jumper Cord (ROW)

Configuration Rules:

Note 1

The following Transceivers install into this Switch

HP X120 1G SFP LC SX Transceiver

JD118B

HP X120 1G SFP LC LX Transceiver

JD119B

HP X120 1G SFP RJ45 T Transceiver

JD089B

HP X120 1G SFP LC BX 10-U Transceiver

JD098B

HP X120 1G SFP LC BX 10-D Transceiver

JD099B

HP X125 1G SFP LC LH40 1310nm Transceiver

JD061A

HP X120 1G SFP LC LH40 1550nm Transceiver

JD062A

HP X125 1G SFP LC LH70 Transceiver

JD063B

Note 3

Localization (Wall Power Cord) required on orders without #B2B, #B2C (PDU Power Cord) or #B2E. (See Localization Menu)

Remark

Drop down under power supply should offer the following options and results:
Switch/Router/Power Supply to PDU Power Cord - #B2B in North America, Mexico, Taiwan, and Japan or #B2C ROW. (Watson Default B2B or B2C for Rack Level CTO)
Switch/Router/Power Supply to Wall Power Cord - Localized Option (Watson Default for BTO and Box Level CTO)
High Volt Switch/Router/Power Supply to Wall Power Cord - #B2E Option. (Offered only in North America, Mexico, Taiwan, and Japan)

Box Level Integration CTO Models

CTO Solution Sku

HP 51xx CTO Switch Solution

JG706A

• SSP trigger sku

CTO Switch Chassis

HP 5120-24G EI Switch - CTO

JE066A

• 24 RJ-45 autosensing 10/100/1000 ports
• 4 dual-personality ports; PoE auto-sensing 10/100/1000Base-T or SFP
• min=0 \ max=4 SFP Transceivers
• 0 port expansion module slots
• 1 - Power Supply Included
• 1U - Height

See Configuration NOTE: 1, 3, 5,7

PDU Cable NA/MEX/TW/JP

JE066A#B2B

• C15 PDU Jumper Cord (NA/MEX/TW/JP)

PDU Cable ROW

JE066A#B2C

• C15 PDU Jumper Cord (ROW)

HP 5120-24G EI Switch with 2 Slots - CTO

JE068A

• 24 RJ-45 autosensing 10/100/1000 ports
• 4 dual-personality ports; PoE auto-sensing 10/100/1000Base-T or SFP
• min=0 \ max=4 SFP Transceivers
• 2 - port expansion module slots
• 1 - Power Supply Included
• 1U - Height

See Configuration NOTE: 1, 3, 5,7

PDU Cable NA/MEX/TW/JP

JE068A#B2B

• C15 PDU Jumper Cord (NA/MEX/TW/JP)

PDU Cable ROW

JE068A#B2C

• C15 PDU Jumper Cord (ROW)

HP 5120-24G-PoE+ EI Switch w/2 Intf Slts - CTO

JG236A

• 24 RJ-45 autosensing 10/100/1000 ports
• 4 dual-personality ports; PoE auto-sensing 10/100/1000Base-T or SFP
• min=0 \ max=4 SFP Transceivers
• 2 - port expansion module slots
• 1 - Power Supply Included
• 1U - Height

See Configuration NOTE: 1, 3, 5,7

PDU Cable NA/MEX/TW/JP

JG236A#B2B

• C15 PDU Jumper Cord (NA/MEX/TW/JP)

PDU Cable ROW

JG236A#B2C

• C15 PDU Jumper Cord (ROW)

HP 5120-48G EI Switch - CTO

JE067A

• 48 RJ-45 autosensing 10/100/1000 ports
• 4 dual-personality ports; PoE auto-sensing 10/100/1000Base-T or SFP
• min=0 \ max=4 SFP Transceivers
• 0 - port expansion module slots
• 1 - Power Supply Included
• 1U - Height

See Configuration NOTE: 1, 3, 4, 5,7

PDU Cable NA/MEX/TW/JP

JE067A#B2B

• C15 PDU Jumper Cord (NA/MEX/TW/JP)

PDU Cable ROW

JE067A#B2C

• C15 PDU Jumper Cord (ROW)

HP 5120-48G EI Switch with 2 Slots - CTO

JE069A

• 48 RJ-45 autosensing 10/100/1000 ports
• 4 dual-personality ports; PoE auto-sensing 10/100/1000Base-T or SFP
• min=0 \ max=4 SFP Transceivers
• 2 - port expansion module slots
• 1 - Power Supply Included
• 1U - Height

See Configuration NOTE: 1, 3, 5,7

PDU Cable NA/MEX/TW/JP

JE069A#B2B

• C15 PDU Jumper Cord (NA/MEX/TW/JP)

PDU Cable ROW

JE069A#B2C

• C15 PDU Jumper Cord (ROW)

HP 5120-48G-PoE+ EI Switch w/2 Intf Slts - CTO

JG237A

• 48 RJ-45 autosensing 10/100/1000 ports
• 4 dual-personality ports; PoE auto-sensing 10/100/1000Base-T or SFP
• min=0 \ max=4 SFP Transceivers
• 2 - port expansion module slots
• 1 - Power Supply Included
• 1U - Height

See Configuration NOTE: 1, 3, 5,7

PDU Cable NA/MEX/TW/JP

JG237A#B2B

• C15 PDU Jumper Cord (NA/MEX/TW/JP)

PDU Cable ROW

JG237A#B2C

• C15 PDU Jumper Cord (ROW)

Configuration Rules:

Note 1

The following Transceivers install into this Switch: (Use #0D1 if switch is CTO)

HP X120 1G SFP LC SX Transceiver

JD118B

HP X120 1G SFP LC LX Transceiver

JD119B

HP X120 1G SFP RJ45 T Transceiver

JD089B

HP X120 1G SFP LC BX 10-U Transceiver

JD098B

HP X120 1G SFP LC BX 10-D Transceiver

JD099B

HP X125 1G SFP LC LH40 1310nm Transceiver

JD061A

HP X120 1G SFP LC LH40 1550nm Transceiver

JD062A

HP X125 1G SFP LC LH70 Transceiver

JD063B

Note 3

Localization (Wall Power Cord) required on orders without #B2B, #B2C (PDU Power Cord) or #B2E. (See Localization Menu)

Note 5

If this Switch is selected, Then a Minimum of 1 factory integrated accessory must be ordered and integrated to CTO chassis. See Menu below, option must have a #0D1 to be integrated to the CTO Chassis.

Note 7

If the Switch Chassis is to be Box Level Factory Integrated (CTO), Then the #0D1 is required on the Switch Chassis and integrated to the JG706A - HP 51xx CTO Enablement. (Min 1/Max 1 Switch per SSP)

Remarks:

Drop down under power supply should offer the following options and results:
Switch/Router/Power Supply to PDU Power Cord - #B2B in North America, Mexico, Taiwan, and Japan or #B2C ROW. (Watson Default B2B or B2C for Rack Level CTO)
Switch/Router/Power Supply to Wall Power Cord - Localized Option (Watson Default for BTO and Box Level CTO)
High Volt Switch/Router/Power Supply to Wall Power Cord - #B2E Option. (Offered only in North America, Mexico, Taiwan, and Japan)

Rack Level Integration CTO Models

Switch Chassis

HP 5120-24G EI Switch

JE066A

• 24 RJ-45 autosensing 10/100/1000 ports
• 4 dual-personality ports; PoE auto-sensing 10/100/1000Base-T or SFP
• min=0 \ max=4 SFP Transceivers
• 0 port expansion module slots
• Power supply included
• 1U - Height

See Configuration NOTE: 1, 3, 10

PDU Cable NA/MEX/TW/JP

JE066A#B2B

• C15 PDU Jumper Cord (NA/MEX/TW/JP)

PDU Cable ROW

JE066A#B2C

• C15 PDU Jumper Cord (ROW)

HP 5120-24G EI Switch with 2 Slots

JE068A

• 24 RJ-45 autosensing 10/100/1000 ports
• 4 dual-personality ports; PoE auto-sensing 10/100/1000Base-T or SFP
• min=0 \ max=4 SFP Transceivers
• 2 port expansion module slots
• Power supply included
• 1U - Height

See Configuration NOTE: 1, 3, 10

PDU Cable NA/MEX/TW/JP

JE068A#B2B

• C15 PDU Jumper Cord (NA/MEX/TW/JP)

PDU Cable ROW

JE068A#B2C

• C15 PDU Jumper Cord (ROW)

HP 5120-24G-PoE+ EI Switch w/2 Intf Slts

JG236A

• 24 RJ-45 autosensing 10/100/1000 ports
• 4 dual-personality ports; PoE auto-sensing 10/100/1000Base-T or SFP
• min=0 \ max=4 SFP Transceivers
• 2 port expansion module slots
• Power supply included
• 1U - Height

See Configuration NOTE: 1, 3, 10

PDU Cable NA/MEX/TW/JP

JG236A#B2B

• C15 PDU Jumper Cord (NA/MEX/TW/JP)

PDU Cable ROW

JG236A#B2C

• C15 PDU Jumper Cord (ROW)

HP 5120-48G EI Switch

JE067A

• 48 RJ-45 autosensing 10/100/1000 ports
• 4 dual-personality ports; PoE auto-sensing 10/100/1000Base-T or SFP
• min=0 \ max=4 SFP Transceivers
• 0 port expansion module slots
• Power supply included
• 1U - Height

See Configuration NOTE: 1, 3, 10

PDU Cable NA/MEX/TW/JP

JE067A#B2B

• C15 PDU Jumper Cord (NA/MEX/TW/JP)

PDU Cable ROW

JE067A#B2C

• C15 PDU Jumper Cord (ROW)

HP 5120-48G EI Switch with 2 Slots

JE069A

• 48 RJ-45 autosensing 10/100/1000 ports
• 4 dual-personality ports; PoE auto-sensing 10/100/1000Base-T or SFP
• min=0 \ max=4 SFP Transceivers
• 2 port expansion module slots
• Power supply included
• 1U - Height

See Configuration NOTE: 1, 3, 10

PDU Cable NA/MEX/TW/JP

JE069A#B2B

• C15 PDU Jumper Cord (NA/MEX/TW/JP)

PDU Cable ROW

JE069A#B2C

• C15 PDU Jumper Cord (ROW)

HP 5120-48G-PoE+ EI Switch w/2 Intf Slts

JG237A

• 48 RJ-45 autosensing 10/100/1000 ports
• 4 dual-personality ports; PoE auto-sensing 10/100/1000Base-T or SFP
• min=0 \ max=4 SFP Transceivers
• 2 port expansion module slots
• Power supply included
• 1U - Height

See Configuration NOTE: 1, 3, 10

PDU Cable NA/MEX/TW/JP

JG237A#B2B

• C15 PDU Jumper Cord (NA/MEX/TW/JP)

PDU Cable ROW

JG237A#B2C

• C15 PDU Jumper Cord (ROW)

Configuration Rules:

Note 1

The following Transceivers install into this Switch:

HP X120 1G SFP LC SX Transceiver

JD118B

HP X120 1G SFP LC LX Transceiver

JD119B

HP X120 1G SFP RJ45 T Transceiver

JD089B

HP X120 1G SFP LC BX 10-U Transceiver

JD098B

HP X120 1G SFP LC BX 10-D Transceiver

JD099B

HP X125 1G SFP LC LH40 1310nm Transceiver

JD061A

HP X120 1G SFP LC LH40 1550nm Transceiver

JD062A

HP X125 1G SFP LC LH70 Transceiver

JD063B

Note 3

Localization (Wall Power Cord) required on orders without #B2B, #B2C (PDU Power Cord) . (See Localization Menu)
REMARK: When Switches/Routers are Factory Racked, Then #B2B, or #B2C should be the Defaulted Power Cable option on the Switches/Routers.

Note 10

If HP CTO Switch Chassis is selected for Rack Level Integration, Then the Switch needs to integrate (with #0D1) to the Rack.

Remarks:

Drop down under power supply should offer the following options and results:
Switch/Router/Power Supply to PDU Power Cord - #B2B in North America, Mexico, Taiwan, and Japan or #B2C ROW. (Watson Default B2B or B2C for Rack Level CTO)
Switch/Router/Power Supply to Wall Power Cord - Localized Option (Watson Default for BTO and Box Level CTO)

Switch Enclosure Options

External/Redundant Power Supplies

HP RPS 800 Redundant Power Supply

JD183A

• Height = 1U
• includes 1 x c13, 800w

See Configuration NOTE: 2, 3

HP RPS1600 Redundant Power System

JG136A

• Height = 1U
• includes 1 x c13, 1600w and Power Supply port

See Configuration NOTE: 2, 3

HP RPS1600 1600W AC Power Supply

JG137A

• Installs into JG136A only

See Configuration NOTE: 1

Configuration Rules:

Note 1

If this power supply is selected, The JG136A - HP A-RPS1600 Redundant Power System must be on order or onsite.

Note 2

Localization required. (See Localization Menu for list.)

Note 3

Only 1 JD183A or JG136A can be connected per switch.

External/Redundant Power Cables

HP X290 1000 A JD5 2m RPS Cable

JD187A

HP X290 500/800 1m RPS Cable

JD190A

Enter the following menu selections as integrated to the CTO Model X above if order is factory built.

Modules

(Switch JE066x and JE067x ) No Modules supported

(All other Switches ) System (std 0 // max 2) User Selection (min 0 // max 2)

HP 5500 2-port 10GbE XFP Module

JD359B

• min=0 \ max=2 XFP Transceivers

See Configuration NOTE: 2, 5, 6

HP 5500 2-port 10GbE Local Connect Mod

JD360B

• min=0 \ max=2 CX4 Cables

See Configuration NOTE: 4, 5, 6

HP 5500 1-port 10GbE XFP Module

JD361B

• min=0 \ max=1 XFP Transceivers

See Configuration NOTE: 2, 5, 6

HP 5500/5120 2-port 10GbE SFP+ Module

JD368B

• min=0 \ max=2 SFP+ Transceivers

See Configuration NOTE: 1, 5, 6

HP 5500/4800 2-port GbE SFP Module

JD367A

• min=0 \ max=2 SFP Transceivers

See Configuration NOTE: 3, 5, 6

HP 5500/5120 2p 10GBASE-T Module

JG535A

• No Transceivers

See Configuration NOTE: 5, 6

Configuration Rules:

Note 1

The following Transceivers install into this Module: (Use #0D1 if switch is CTO)

HP X130 10G SFP+ LC ER 40km Transceiver

JG234A

HP X130 10G SFP+ LC SR Transceiver

JD092B

HP X130 10G SFP+ LC LRM Transceiver

JD093B

HP X130 10G SFP+ LC LR Transceiver

JD094B

HP X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable

JD095C

HP X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable

JD096C

HP X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable

JD097C

HP X240 10G SFP+ SFP+ 7m Direct Attach Copper Cable

JC784C

HP X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable

JG081C

HP X240 10G SFP+ SFP+ 7m Direct Attach Copper Cable

JC784C

Note 2

The following Transceivers install into this Module: (Use #0D1 if switch is CTO)

HP X135 10G XFP LC ER Transceiver

JD121A

HP X130 10G XFP LC LR Single Mode 10km 1310nm Transceiver

JD108B

HP X130 10G XFP LC SR Transceiver

JD117B

Note 3

The following Transceivers install into this Module: (Use #0D1 if switch is CTO)

HP X120 1G SFP LC SX Transceiver

JD118B

HP X120 1G SFP LC LX Transceiver

JD119B

HP X120 1G SFP RJ45 T Transceiver

JD089B

HP X120 1G SFP LC BX 10-U Transceiver

JD098B

HP X120 1G SFP LC BX 10-D Transceiver

JD099B

HP X125 1G SFP LC LH40 1310nm Transceiver

JD061A

HP X120 1G SFP LC LH40 1550nm Transceiver

JD062A

HP X125 1G SFP LC LH70 Transceiver

JD063B

Note 4

The following Cables install into this Module: (Use #B01 if switch is CTO)

HP X230 Local Connect 50cm CX4 Cable

JD363B

HP X230 Local Connect 100cm CX4 Cable

JD364B

HP X230 CX4 to CX4 3m Cable

JD365A

NOTE: Two JD365A - HP X230 CX4 to CX4 3m Cable should be added by default if Module is selected.

Note 5

If factory intergrated into the switch, This Module must be ordered as #0D1 when the switch is not Factory Racked

Note 6

If factory intergrated into the switch, This Module must be ordered as #B01 when the switch is Factory Racked (Rack Level Integration CTO).

Transceivers

SFP Transceivers

HP X120 1G SFP LC SX Transceiver

JD118B

HP X120 1G SFP LC LX Transceiver

JD119B

HP X120 1G SFP RJ45 T Transceiver

JD089B

HP X120 1G SFP LC BX 10-U Transceiver

JD098B

HP X120 1G SFP LC BX 10-D Transceiver

JD099B

HP X120 1G SFP LC LH40 1550nm XCVR

JD062A

HP X125 1G SFP LC LH40 1310nm Transceiver

JD061A

HP X125 1G SFP LC LH70 Transceiver

JD063B

SFP+ Transceivers

HP X130 10G SFP+ LC ER 40km Transceiver

JG234A

HP X130 10G SFP+ LC SR Transceiver

JD092B

HP X130 10G SFP+ LC LRM Transceiver

JD093B

HP X130 10G SFP+ LC LR Transceiver

JD094B

HP X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable

JD095C

HP X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable

JD096C

HP X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable

JD097C

HP X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable

JG081C

HP X240 10G SFP+ SFP+ 7m Direct Attach Copper Cable

JC784C

XFP Transceivers

HP X130 10G XFP LC LR Single Mode 10km 1310nm Transceiver

JD108B

HP X130 LC SR XFP Transceiver

JD117B

HP X135 10G XFP LC ER Transceiver

JD121A

Cables

Local Connect Cables

HP X230 Local Connect 50cm CX4 Cable

JD363B

HP X230 Local Connect 100cm CX4 Cable

JD364B

HP X230 CX4 to CX4 3m Cable

JD365A

HP X230 Local Connect 50cm CX4 Cable

JD363B

HP X230 Local Connect 100cm CX4 Cable

JD364B

HP X230 CX4 to CX4 3m Cable

JD365A

Multi-Mode Cables

HP .5m Multi-mode OM3 LC/LC FC Cable

AJ833A

HP 1m Multi-mode OM3 LC/LC FC Cable

AJ834A

HP 2 m Multimode OM3 LC/LC FC Cable

AJ835A

HP 5 m Multimode OM3 LC/LC FC Cable

AJ836A

HP 15 m Multimode OM3 LC/LC FC Cable

AJ837A

HP 30 m Multimode OM3 LC/LC FC Cable

AJ838A

HP 50 m Multimode OM3 LC/LC FC Cable

AJ839A

HP Premier Flex LC/LC OM4 2f 1m Cbl

QK732A

HP Premier Flex LC/LC OM4 2f 2m Cbl

QK733A

HP Premier Flex LC/LC OM4 2f 5m Cbl

QK734A

HP Premier Flex LC/LC OM4 2f 15m Cbl

QK735A

HP Premier Flex LC/LC OM4 2f 30m Cbl

QK736A

HP Premier Flex LC/LC OM4 2f 50m Cbl

QK737A

Opacity Shield Kit

(System (std 0 // max 1) User Selection (min 0 // max 1)

HP 5500/5120 Gig-T EI Opcty Shld Kit

JG557A

• Supported on JG245A, JG246A

See Configuration NOTE: 1

HP 5500/5120 Gig-T PoE EI Opcty Shld Kit

JG559A

• Supported on JG247A, JG248A

See Configuration NOTE: 1

Configuration Rules:

Note 1

If selected with a CTO Switch Solution, Quantity 1 of JG585A#B01 must also be ordered.

Tamper Evidence Labels

(System (std 0 // max 1) User Selection (min 0 // max 1)

HP 12mm x 60mm Tmpr-Evidence (30) Lbl

JG585A

• Supported on JG557A or JG559A

See Configuration NOTE: 1

Configuration Rules:

Note 1

If selected with a CTO Switch Solution, Quantity 1 of JG557A#B01 or JG559A#B01 must also be ordered.

Remarks:

Each JG557A or JG559A would use 1 of JG585A

HP 5120-48G EI Switch with 2 Interface Slots (JE069A)

Ports

48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Media Type: Auto-MDIX; Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only

4 dual-personality ports; auto-sensing 10/100/1000Base-T or SFP

2 port expansion module slots

1 RJ-45 serial console port

Supports a maximum of 48 autosensing 10/100/1000 ports

Physical characteristics

Dimensions

17.32(w) x 11.81(d) x 1.72(h) in (44 x 30 x 4.36 cm) (1U height)

Weight

11.02 lb. (5 kg)

Memory and processor

128 MB SDRAM; Packet buffer size: 4 MB, 16 MB flash

Mounting

Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included)

Performance

1000 Mb Latency

< 3.2 µs

10 Gbps Latency

< 2.6 µs

Throughput

142.9 million pps

Routing/Switching capacity

192 Gbps

Routing table size

32 entries (IPv4)

Environment

Operating temperature

32°F to 113°F (0°C to 45°C)

Operating relative humidity

10% to 90%, noncondensing

Nonoperating/Storage temperature

-40°F to 158°F (-40°C to 70°C)

Nonoperating/Storage relative humidity

5% to 95%, noncondensing

Acoustic

Low-speed fan: 41.3 dB, High-speed fan: 50.1 dB; ISO 7779

Electrical characteristics

Maximum heat dissipation

495 BTU/hr (522.23 kJ/hr)

Voltage

100 - 240 VAC, rated

(depending on power supply chosen)

Idle power

55 W

Maximum power rating

145 W

Frequency

50/60 Hz

Notes

Idle power is the actual power consumption of the device with no ports connected.
Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated.

Safety

UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST; EN 60950-1/A11; FDA 21 CFR Subchapter J; NOM; ROHS Compliance

Emissions

FCC part 15 Class A; VCCI Class A; EN 55022 Class A; CISPR 22 Class A; ICES-003 Class A; ANSI C63.4 2003; ETSI EN 300 386 V1.3.3; AS/NZS CISPR22 Class A; EN 61000-3-2; EN 61000-3-3; EN 61000-4-2; EN 61000-4-3; EN 61000-4-4; EN 61000-4-5; EN 61000-4-6; EN 61000-4-11; EN 61000-3-2:2006; EN 61000-3-3:1995 +A1:2001+A2:2005; EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A

Management

IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager

Services

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HP 5120-48G EI Switch (JE067A)

Ports

48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Media Type: Auto-MDIX; Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only

4 dual-personality ports; auto-sensing 10/100/1000Base-T or SFP

1 RJ-45 serial console port

Supports a maximum of 48 autosensing 10/100/1000 ports

Physical characteristics

Dimensions

17.32(w) x 11.81(d) x 1.72(h) in (44 x 30 x 4.37 cm) (1U height)

Weight

11.02 lb. (5 kg)

Memory and processor

128 MB SRAM; Packet buffer size: 4 MB, 16 MB flash

Mounting

Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included)

Performance

1000 Mb Latency

< 3.2 µs

Throughput

71.4 million pps

Routing/Switching capacity

96 Gbps

Routing table size

32 entries (IPv4)

10 Gbps Latency

< 2.6 µs

Environment

Operating temperature

32°F to 113°F (0°C to 45°C)

Operating relative humidity

10% to 90%, noncondensing

Nonoperating/Storage temperature

-40°F to 158°F (-40°C to 70°C)

Nonoperating/Storage relative humidity

5% to 95%, noncondensing

Acoustic

Low-speed fan: 41.3 dB, High-speed fan: 50.1 dB; ISO 7779

Electrical characteristics

Maximum heat dissipation

375 BTU/hr (395.63 kJ/hr)

Voltage

100 - 240 VAC, rated

(depending on power supply chosen)

Idle power

54 W

Maximum power rating

110 W

Frequency

50/60 Hz

Notes

Idle power is the actual power consumption of the device with no ports connected.
Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated.

Safety

UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST; EN 60950-1/A11; FDA 21 CFR Subchapter J; NOM; ROHS Compliance

Emissions

FCC part 15 Class A; VCCI Class A; EN 55022 Class A; CISPR 22 Class A; ICES-003 Class A; ANSI C63.4 2003; ETSI EN 300 386 V1.3.3; AS/NZS CISPR22 Class A; EN 61000-3-2; EN 61000-3-3; EN 61000-4-2; EN 61000-4-3; EN 61000-4-4; EN 61000-4-5; EN 61000-4-6; EN 61000-4-11; EN 61000-3-2:2006; EN 61000-3-3:1995 +A1:2001+A2:2005; EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A

Management

IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager

Services

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HP 5120-24G EI Switch with 2 Interface Slots (JE068A)

Ports

24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only

4 dual-personality ports; auto-sensing 10/100/1000Base-T or SFP

2 port expansion module slots

1 RJ-45 serial console port

Physical characteristics

Dimensions

17.32(w) x 11.81(d) x 1.72(h) in (44 x 30 x 4.37 cm) (1U height)

Weight

9.92 lb. (4.5 kg)

Memory and processor

128 MB SDRAM; Packet buffer size: 2 MB, 16 MB flash

Mounting

Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included)

Performance

1000 Mb Latency

< 3.2 µs

10 Gbps Latency

< 2.6 µs

Throughput

107.2 million pps

Routing/Switching capacity

144 Gbps

Routing table size

32 entries (IPv4)

Environment

Operating temperature

32°F to 113°F (0°C to 45°C)

Operating relative humidity

10% to 90%, noncondensing

Nonoperating/Storage temperature

-40°F to 158°F (-40°C to 70°C)

Nonoperating/Storage relative humidity

5% to 95%, noncondensing

Acoustic

Low-speed fan: 42.6 dB, High-speed fan: 49.7 dB; ISO 7779

Electrical characteristics

Maximum heat dissipation

351 BTU/hr (370.3 kJ/hr)

Voltage

100 - 240 VAC, rated

(depending on power supply chosen)

Idle power

36 W

Maximum power rating

103 W

Frequency

50/60 Hz

Notes

Idle power is the actual power consumption of the device with no ports connected.
Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated.

Safety

UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST; EN 60950-1/A11; FDA 21 CFR Subchapter J; NOM; ROHS Compliance

Emissions

FCC part 15 Class A; VCCI Class A; EN 55022 Class A; CISPR 22 Class A; ICES-003 Class A; ANSI C63.4 2003; ETSI EN 300 386 V1.3.3; AS/NZS CISPR22 Class A; EN 61000-3-2; EN 61000-3-3; EN 61000-4-2; EN 61000-4-3; EN 61000-4-4; EN 61000-4-5; EN 61000-4-6; EN 61000-4-11; EN 61000-3-2:2006; EN 61000-3-3:1995 +A1:2001+A2:2005; EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A

Management

IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager

Services

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HP 5120-24G EI Switch (JE066A)

Ports

24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only

4 dual-personality ports; auto-sensing 10/100/1000Base-T or SFP

1 RJ-45 serial console port

Physical characteristics

Dimensions

17.32(w) x 11.81(d) x 1.72(h) in (44 x 30 x 4.36 cm) (1U height)

Weight

9.92 lb. (4.5 kg)

Memory and processor

128 MB SDRAM; Packet buffer size: 2 MB, 16 MB flash

Mounting

Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included)

Performance

1000 Mb Latency

< 3.2 µs

Throughput

35.7 million pps

Routing/Switching capacity

48 Gbps

Routing table size

32 entries (IPv4)

10 Gbps Latency

< 2.6 µs

Environment

Operating temperature

32°F to 113°F (0°C to 45°C)

Operating relative humidity

10% to 90%, noncondensing

Nonoperating/Storage temperature

-40°F to 158°F (-40°C to 70°C)

Nonoperating/Storage relative humidity

5% to 95%, noncondensing

Acoustic

Low-speed fan: 42.6 dB, High-speed fan: 49.7 dB; ISO 7779

Electrical characteristics

Maximum heat dissipation

212 BTU/hr (223.66 kJ/hr)

Voltage

100 - 240 VAC, rated

(depending on power supply chosen)

Idle power

35 W

Maximum power rating

62 W

Frequency

50/60 Hz

Notes

Idle power is the actual power consumption of the device with no ports connected.
Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated.

Safety

UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST; EN 60950-1/A11; FDA 21 CFR Subchapter J; NOM; ROHS Compliance

Emissions

FCC part 15 Class A; VCCI Class A; EN 55022 Class A; CISPR 22 Class A; ICES-003 Class A; ANSI C63.4 2003; ETSI EN 300 386 V1.3.3; AS/NZS CISPR22 Class A; EN 61000-3-2; EN 61000-3-3; EN 61000-4-2; EN 61000-4-3; EN 61000-4-4; EN 61000-4-5; EN 61000-4-6; EN 61000-4-11; EN 61000-3-2:2006; EN 61000-3-3:1995 +A1:2001+A2:2005; EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A

Management

IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager

Services

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HP 5120-48G-PoE+ EI Switch with 2 Interface Slots (JG237A)

Ports

48 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at PoE+); Media Type: Auto-MDIX; Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only

4 dual-personality ports; PoE auto-sensing 10/100/1000Base-T or SFP

2 port expansion module slots

1 RJ-45 serial console port

Supports a maximum of 48 autosensing 10/100/1000 ports

Physical characteristics

Dimensions

17.32(w) x 16.54(d) x 1.72(h) in (43.99 x 42.01 x 4.37 cm) (1U height)

Weight

16.53 lb. (7.5 kg)

Memory and processor

128 MB SDRAM; Packet buffer size: 4 MB, 16 MB flash

Mounting

Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included)

Performance

1000 Mb Latency

< 3.2 µs

10 Gbps Latency

< 2.6 µs

Throughput

142.9 million pps

Routing/Switching capacity

192 Gbps

Routing table size

32 entries (IPv4)

Environment

Operating temperature

32°F to 113°F (0°C to 45°C)

Operating relative humidity

10% to 90%, noncondensing

Nonoperating/Storage temperature

-40°F to 158°F (-40°C to 70°C)

Nonoperating/Storage relative humidity

10% to 90%, noncondensing

Acoustic

Low-speed fan: 49.5 dB, High-speed fan: 54.1 dB; ISO 7779

Electrical characteristics

Maximum heat dissipation

2221 BTU/hr (2343.15 kJ/hr), Max heat dissipation for AC is 2221 BTU/hr and 3142 BTU/hr for RPS (Redundant Power Supply).

Voltage

100 - 240 VAC, rated

(depending on power supply chosen)

Idle power

90 W

Maximum power rating

651 W

PoE power

370 W PoE+

Frequency

50/60 Hz

Notes

Idle power is the actual power consumption of the device with no ports connected.
Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated.
PoE Power is the power supplied by the internal power supply; it is dependent on the type and quantity of power supplies and may be supplemented with the use of an External Power Supply (EPS).
With AC input, the Max power consumption is 550 W (370 W for PoE).

Safety

UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST; EN 60950-1/A11; FDA 21 CFR Subchapter J; NOM; ROHS Compliance

Emissions

FCC part 15 Class A; VCCI Class A; EN 55022 Class A; CISPR 22 Class A; ICES-003 Class A; ANSI C63.4 2003; ETSI EN 300 386 V1.3.3; AS/NZS CISPR22 Class A; EN 61000-3-2; EN 61000-3-3; EN 61000-4-2; EN 61000-4-3; EN 61000-4-4; EN 61000-4-5; EN 61000-4-6; EN 61000-4-11; EN 61000-3-2:2006; EN 61000-3-3:1995 +A1:2001+A2:2005; EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A

Management

IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager

Services

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HP 5120-24G-PoE+ EI Switch with 2 Interface Slots (JG236A)

Ports

24 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at PoE+); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only

4 dual-personality ports; PoE auto-sensing 10/100/1000Base-T or SPF

2 port expansion module slots

1 RJ-45 serial console port

Physical characteristics

Dimensions

17.32(w) x 16.54(d) x 1.72(h) in (43.99 x 42.01 x 4.37 cm) (1U height)

Weight

15.43 lb. (7 kg)

Memory and processor

128 MB SDRAM; Packet buffer size: 2 MB, 16 MB flash

Mounting

Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included)

Performance

1000 Mb Latency

< 3.2 µs

10 Gbps Latency

< 2.6 µs

Throughput

107.2 million pps

Routing/Switching capacity

144 Gbps

Routing table size

32 entries (IPv4)

Environment

Operating temperature

32°F to 113°F (0°C to 45°C)

Operating relative humidity

10% to 90%, noncondensing

Nonoperating/Storage temperature

-40°F to 158°F (-40°C to 70°C)

Nonoperating/Storage relative humidity

5% to 95%, noncondensing

Acoustic

Low-speed fan: 41.5 dB, High-speed fan: 51.1 dB; ISO 7779

Electrical characteristics

Maximum heat dissipation

1996 BTU/hr (2105.78 kJ/hr), Max heat dissipation for AC is 1996 BTU/hr and 1675 BTU/hr for RPS (Redundant Power Supply).

Voltage

100 - 240 VAC, rated

(depending on power supply chosen)

Idle power

65 W

Maximum power rating

585 W

PoE power

370 W

Frequency

50/60 Hz

Notes

Idle power is the actual power consumption of the device with no ports connected.

Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated.&lt;br&gt;PoE power is the power supplied by the internal power supply. It is dependent on the type and quantity of power supplies and may be supplemented with the use of an external power supply (EPS).

With AC input, the maximum power consumption is 585W; 215W for system, 370W for PoE. With DC input, the maximum power consumption is 491W; 121W for system, 370W for PoE.

Safety

UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST; EN 60950-1/A11; FDA 21 CFR Subchapter J; NOM; ROHS Compliance

Emissions

FCC part 15 Class A; VCCI Class A; EN 55022 Class A; CISPR 22 Class A; ICES-003 Class A; ANSI C63.4 2003; ETSI EN 300 386 V1.3.3; AS/NZS CISPR22 Class A; EN 61000-3-2; EN 61000-3-3; EN 61000-4-2; EN 61000-4-3; EN 61000-4-4; EN 61000-4-5; EN 61000-4-6; EN 61000-4-11; EN 61000-3-2:2006; EN 61000-3-3:1995 +A1:2001+A2:2005; EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A

Management

IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager

Services

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

Standards and protocols
(applies to all products in series)

Device management
RFC 1157 SNMPv1/v2c
RFC 1305 NTPv3
RFC 2573 (SNMPv3 Applications)
RFC 2819 (RMON groups Alarm, Event, History
and Statistics only)
RFC 3416 (SNMP Protocol Operations v2)
HTML and telnet management
Multiple Configuration Files
SNMP v3 and RMON RFC support
SSHv1/SSHv2 Secure Shell
TACACS/TACACS+
Web UI

General protocols
IEEE 802.1ad Q-in-Q
IEEE 802.1D MAC Bridges
IEEE 802.1p Priority
IEEE 802.1Q VLANs
IEEE 802.1s Multiple Spanning Trees
IEEE 802.1w Rapid Reconfiguration of Spanning Tree
IEEE 802.1X PAE
IEEE 802.3 Type 10BASE-T
IEEE 802.3ab 1000BASE-T
IEEE 802.3ad Link Aggregation Control Protocol (LACP)
IEEE 802.3ae 10-Gigabit Ethernet
IEEE 802.3af Power over Ethernet
IEEE 802.3i 10BASE-T
IEEE 802.3u 100BASE-X
IEEE 802.3x Flow Control
IEEE 802.3z 1000BASE-X
RFC 768 UDP
RFC 783 TFTP Protocol (revision 2)
RFC 791 IP
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 TELNET
RFC 951 BOOTP
RFC 1213 Management Information Base for Network Management of TCP/IP-based internets
RFC 1305 NTPv3
RFC 1350 TFTP Protocol (revision 2)
RFC 1519 CIDR
RFC 1812 IPv4 Routing
RFC 1866 Hypertext Markup Language - 2.0
RFC 2131 DHCP
RFC 2236 IGMP Snooping
RFC 2616 HTTP Compatibility v1.1
RFC 2665 Definitions of Managed Objects for the Ethernet-like Interface Types
RFC 2668 Definitions of Managed Objects for IEEE 802.3 Medium Attachment Units (MAUs)
RFC 2865 Remote Authentication Dial In User Service (RADIUS)
RFC 2866 RADIUS Accounting
RFC 3414 User-based Security Model (USM) for version 3 of the Simple Network Management Protocol (SNMPv3)
RFC 3415 View-based Access Control Model (VACM) for the Simple Network Management Protocol (SNMP)
RFC 3418 Management Information Base (MIB) for the Simple Network Management Protocol (SNMP)
RFC 4213 Basic IPv6 Transition Mechanisms
802.1r - GARP Proprietary Attribute Registration Protocol (GPRP)

IPv6
RFC 2461 IPv6 Neighbor Discovery
RFC 2463 ICMPv6
RFC 3162 RADIUS and IPv6
RFC 3306 Unicast-Prefix-based IPv6 Multicast
Addresses
RFC 3315 DHCPv6 (client and relay)

MIBs
RFC 1212 Concise MIB Definitions
RFC 1213 MIB II
RFC 1493 Bridge MIB
RFC 1757 Remote Network Monitoring MIB
RFC 2096 IP Forwarding Table MIB
RFC 2233 Interface MIB
RFC 2571 SNMP Framework MIB
RFC 2572 SNMP-MPD MIB
RFC 2573 SNMP-Notification MIB
RFC 2573 SNMP-Target MIB
RFC 2574 SNMP USM MIB
RFC 2618 RADIUS Authentication Client MIB
RFC 2620 RADIUS Accounting Client MIB
RFC 2665 Ethernet-Like-MIB
RFC 2668 802.3 MAU MIB
RFC 2674 802.1p and IEEE 802.1Q Bridge MIB
RFC 2737 Entity MIB (Version 2)
RFC 2819 RMON MIB
RFC 2863 The Interfaces Group MIB
RFC 2925 Ping MIB
RFC 3414 SNMP-User based-SM MIB
RFC 3415 SNMP-View based-ACM MIB
RFC 3418 MIB for SNMPv3
RFC 3621 Power Ethernet MIB

Network management
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
RFC 2819 Four groups of RMON: 1 (statistics), 2
(history), 3 (alarm) and 9 (events)
ANSI/TIA-1057 LLDP Media Endpoint Discovery
(LLDP-MED)
SNMPv1/v2c/v3

Security
IEEE 802.1X Port Based Network Access Control
RFC 1492 TACACS+
RFC 2138 RADIUS Authentication
RFC 2139 RADIUS Accounting
RFC 2865 RADIUS (client only)
RFC 2866 RADIUS Accounting
Secure Sockets Layer (SSL)
SSHv2 Secure Shell

HPE 5120 EI Switch Series accessories

Modules

HP 5500 2-port 10GbE XFP Module

JD359B

HP 5500 2-port 10GbE Local Connect Module

JD360B

HP 5500 1-port 10GbE XFP Module

JD361B

HP 5500/5120 2-port 10GbE SFP+ Module

JD368B

HP 5500/4800 2-port GbE SFP Module

JD367A

HP 5500/5120 2-port 10GBASE-T Module

JG535A

HPE 5130/5510 10GBASE-T 2-port Module

JH156A

Transceivers

HP X125 1G SFP LC LH40 1310nm Transceiver

JD061A

HP X120 1G SFP LC LH40 1550nm Transceiver

JD062A

HP X125 1G SFP LC LH70 Transceiver

JD063B

HP X120 1G SFP LC SX Transceiver

JD118B

HP X130 10G SFP+ LC SR Transceiver

JD092B

HP X130 10G SFP+ LC LRM Transceiver

JD093B

HP X130 10G SFP+ LC LR Transceiver

JD094B

HP X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable

JD095C

HP X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable

JD096C

HP X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable

JD097C

HP X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable

JG081C

HP X240 10G SFP+ SFP+ 7m Direct Attach Copper Cable

JC784C

HP X130 10G XFP LC LR Transceiver

JD108B

HP X130 10G XFP LC SR Transceiver

JD117B

HP X120 1G SFP LC SX Transceiver

JD118B

HP X120 1G SFP LC LX Transceiver

JD119B

HP X120 1G SFP RJ45 T Transceiver

JD089B

HP X135 10G XFP LC ER Transceiver

JD121A

HP X120 1G SFP LC BX 10-U Transceiver

JD098B

HP X120 1G SFP LC BX 10-D Transceiver

JD099B

HP X120 1G SFP RJ45 T Transceiver

JD089B

HP X130 10G SFP+ LC ER 40km Transceiver

JG234A

Cables

HP X230 CX4 to CX4 3m Cable

JD365A

HP 0.5 m Multimode OM3 LC/LC Optical Cable

AJ833A

HP 1 m Multimode OM3 LC/LC Optical Cable

AJ834A

HP 2 m Multimode OM3 LC/LC Optical Cable

AJ835A

HP 5 m Multimode OM3 LC/LC Optical Cable

AJ836A

HP 15 m Multimode OM3 LC/LC Optical Cable

AJ837A

HP 30 m Multimode OM3 LC/LC Optical Cable

AJ838A

HP 50 m Multimode OM3 LC/LC Optical Cable

AJ839A

HP Premier Flex LC/LC Multi-mode OM4 2 fiber 1m Cable

QK732A

HP Premier Flex LC/LC Multi-mode OM4 2 fiber 2m Cable

QK733A

HP Premier Flex LC/LC Multi-mode OM4 2 fiber 5m Cable

QK734A

HP Premier Flex LC/LC Multi-mode OM4 2 fiber 15m Cable

QK735A

HP Premier Flex LC/LC Multi-mode OM4 2 fiber 30m Cable

QK736A

HP Premier Flex LC/LC Multi-mode OM4 2 fiber 50m Cable

QK737A

HP X230 Local Connect 50cm CX4 Cable

JD363B

Power Supply

HP RPS 800 Redundant Power Supply

JD183A

HP RPS1600 Redundant Power System

JG136A

HP RPS1600 1600W AC Power Supply

JG137A

Power Cords

HP X290 1000 A JD5 2m RPS Cable

JD187A

HP X290 500/800 1m RPS Cable

JD190A

NOTE: Details are not available for all accessories. The following specifications were available at the time of publication.

HP 5500 2-port 10GbE XFP Module (JD359B)

Ports

2 XFP 10-GbE ports; Duplex: full only

Services

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HP 5500 1-port 10GbE XFP Module (JD361B)

Ports

1 XFP 10-GbE port; Duplex: full only

Services

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HP 5500/4800 2-port GbE SFP Module (JD367A)

Ports

2 SFP 1000 Mbps ports

Services

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HP X125 1G SFP LC LH40 1310nm Transceiver (JD061A)

A small form-factor pluggable SFP Gigabit LH40 transceiver that provides a full duplex Gigabit solution up to 40km on a single-mode fiber.

Ports

1 LC 1000Base-LH port (no IEEE standard exists for 1550 nm optics)

Connectivity

Connector type

LC

Wavelength

1310 nm

Physical characteristics

Dimensions

2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17 cm)

Full configuration weight

0.04 lb. (0.02 kg)

Electrical characteristics

Power consumption typical

0.8 W

Power consumption maximum

1.0 W

Cabling

Cable type:
Single-mode fiber optic, complying with ITU-T G.652;

Maximum distance:

• 40km distance

Fiber type

Single Mode

Services

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HP X120 1G SFP LC LH40 1550nm Transceiver (JD062A)

A small form-factor pluggable (SFP) Gigabit LH40 transceiver that provides a full-duplex Gigabit solution up to 40 km on a single mode fiber.

Ports

1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics)

Connectivity

Connector type

LC

Wavelength

1550 nm

Physical characteristics

Dimensions

2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17 cm)

Full configuration weight

0.04 lb. (0.02 kg)

Electrical characteristics

Power consumption typical

0.8 W

Power consumption maximum

1.0 W

Cabling

Cable type:
Single-mode fiber optic, complying with ITU-T G.652;

Maximum distance:

• 40km distance

Fiber type

Single Mode

Services

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HP X125 1G SFP LC LH70 Transceiver (JD063B)

A small form-factor pluggable (SFP) Gigabit LH70 transceiver that provides a full-duplex Gigabit solution up to 70km on a single-mode fiber.

Ports

1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics)

Connectivity

Connector type

LC

Wavelength

1550 nm

Physical characteristics

Dimensions

2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17 cm)

Full configuration weight

0.04 lb. (0.02 kg)

Electrical characteristics

Power consumption typical

0.8 W

Power consumption maximum

1.0 W

Cabling

Cable type:
Single-mode fiber optic, complying with ITU-T G.652;

Maximum distance:
70km

Fiber type

Single Mode

Services

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HP X120 1G SFP LC SX Transceiver (JD118B)

A small form-factor pluggable (SFP) Gigabit SX transceiver that provides a full-duplex Gigabit solution up to 550m on a Multimode fiber.

Ports

1 LC 1000BASE-SX port

Connectivity

Connector type

LC

Wavelength

850 nm

Physical characteristics

Dimensions

2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17 cm)

Full configuration weight

0.04 lb. (0.02 kg)

Electrical characteristics

Power consumption typical

0.8 W

Power consumption maximum

1.0 W

Cabling

Maximum distance:
FDDI Grade distance = 220m
OM1 = 275m
OM2 = 500m
OM3 = Not Specified by standard

Cable length

up to 550m

Fiber type

Multi Mode

Services

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HP X120 1G SFP LC LX Transceiver (JD119B)

A small form-factor pluggable (SFP) Gigabig LX transceiver that provides a full duplex Gigabit solution up to 550m on MMF or 10Km on SMF

Ports

1 SFP 1000BASE-LX port (IEEE 802.3z Type 1000BASE-LX)

Connectivity

Connector type

LC

Wavelength

1300 nm

Physical characteristics

Dimensions

2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17 cm)

Full configuration weight

0.04 lb. (0.02 kg)

Electrical characteristics

Power consumption typical

0.8 W

Power consumption maximum

1.0 W

Cabling

Cable type:
Either single mode or multimode;

Maximum distance:
550m for Multimode
10km for Singlemode

Fiber type

Both

Services

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HP X120 1G SFP LC BX 10-U Transceiver (JD098B)

A small form-factor pluggable (SFP) Gigabit LX-BX10-U transceiver that provides a full duplex Gigabit solution up to 10km on a single mode cable.

Ports

1 LC 1000BASE-BX10 port (IEEE 802.3ah Type 1000BASE-BX10-U); Duplex: full only

Connectivity

Connector type

LC

Physical characteristics

Dimensions

2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17 cm)

Full configuration weight

0.04 lb. (0.02 kg)

Electrical characteristics

Power consumption typical

0.8 W

Power consumption maximum

1.0 W

Cabling

Maximum distance:
10km

Fiber type

Single Mode

Notes

TX 1310nm RX 1490nm

Services

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HP X120 1G SFP LC BX 10-D Transceiver (JD099B)

A small form-factor pluggable (SFP) Gigabit LX-BX10-D transceiver that provides a full duplex Gigabit solution up to 10km on a single mode cable.

Ports

1 LC 1000BASE-BX10 port (IEEE 802.3ah Type 1000BASE-BX10-D); Duplex: full only

Connectivity

Connector type

LC

Physical characteristics

Dimensions

2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17 cm)

Full configuration weight

0.04 lb. (0.02 kg)

Electrical characteristics

Power consumption typical

0.8 W

Power consumption maximum

1.0 W

Cabling

Maximum distance:
Up to 10km

Fiber type

Single Mode

Notes

TX 1490nm RX 1310nm

Services

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HP X125 1G SFP RJ45 T Transceiver (JD089B)

A small form factor pluggable (SFP) Gigabit 1000Base-T transceiver that provides a full duplex Gigabit solution up to 100m on a Cat-5+ cable.

Ports

1 RJ-45 1000BASE-T port (IEEE 802.3ab Type 1000BASE-T)

Connectivity

Connector type

RJ-45

Physical characteristics

Dimensions

2.71(d) x 0.54(w) x 0.55(h) in. (6.88 x 1.37 x 1.4 cm)

Full configuration weight

0.07 lb. (0.03 kg)

Electrical characteristics

Power consumption typical

0.8 W

Power consumption maximum

1.0 W

Cabling

Cable type:
1000BASE-T: Category 5 (5E or better recommended), 100 Ù differential 4-pair unshielded twisted pair (UTP) or shielded twisted pair (STP) balanced, complying with IEEE 802.3ab 1000BASE-T;

Maximum distance:
100m

Services

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HP 0.5 m Multimode OM3 LC/LC Optical Cable (AJ833A)

Cabling

Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of up to 300 m

Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m

Notes

Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um fiber optic cable and Ethernet assembly with LC duplex connectors on one end and LC duplex connectors on other end.

• Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um Coating diameter: 245 ± 10um
• Optical glass: Bandwidth: For LED sources: 1500/500 MHz-km @850/1300nm.
• Optical glass: Bandwidth: For Laser sources: 2000/500 MHz-km @850/1300nm. VCSEL Laser sources: 600 / 600 meters @850/1300nm for Gigabit Ethernet compliant links.
• CABLE: The cable is duplex zipcord graded index 50/125um multimode optical fiber and designed to work in both the 850 and 1300 nm wavelength windows.
• BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
• Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
• Jacket Color: Aqua for OM3 multimode per TIA 598
• Boot Color: White
• Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M added for lengths > 30 meters.
• Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310 nm @ 23°C as tested in accordance with EIA 455-46.
• Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg

Services

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HP 1 m Multimode OM3 LC/LC Optical Cable (AJ834A)

Cabling

Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of up to 300 m

Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m

Notes

Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um fiber optic cable and Ethernet assembly with LC duplex connectors on one end and LC duplex connectors on other end.

• Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um Coating diameter: 245 ± 10um
• Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km @850/1300nm.
• Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm. VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for Gigabit Ethernet compliant links.
• CABLE: The cable is duplex zipcord graded index 50/125um multimode optical fiber. The cable is designed to work in both the 850 and 1300 nm wavelength windows.
• BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
• Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
• Jacket Color: Aqua for OM3 multimode per TIA 598
• Boot Color: White
• Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M added for lengths > 30 meters.
• Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310 nm @ 23°C as tested in accordance with EIA 455-46.
• Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg

Services

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HP 2 m Multimode OM3 LC/LC Optical Cable (AJ835A)

Cabling

Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of up to 300 m;

Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m

Notes

Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um fiber optic cable and Ethernet assembly with LC duplex connectors on one end and LC duplex connectors on other end.

• Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um Coating diameter: 245 ± 10um
• Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km @850/1300nm.
• Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm. VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for Gigabit Ethernet compliant links.
• CABLE: The cable is duplex zipcord graded index 50/125um multimode optical fiber. The cable is designed to work in both the 850 and 1300 nm wavelength windows.
• BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
• Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
• Jacket Color: Aqua for OM3 multimode per TIA 598
• Boot Color: White
• Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M added for lengths > 30 meters.
• Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310 nm @ 23°C as tested in accordance with EIA 455-46.
• Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg

Services

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HP 5 m Multimode OM3 LC/LC Optical Cable (AJ836A)

Cabling

Cable type:
50/125 µm core/cladding) diameter, mulitimode fiber optic, with effective modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of up to 300 m;

Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m

Notes

Cable Specs: This specification defines the detail requirements for a tight buffered duplex fiber optic multimode OM3 50/125 um fiber optic cable and Ethernet assembly with LC duplex connectors on one end and LC duplex connectors on other end.

• Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um Coating diameter: 245 ± 10um
• Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km @850/1300nm.
• Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm. VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for Gigabit Ethernet compliant links.
• CABLE: The cable is duplex zipcord graded index 50/125um multimode optical fiber. The cable is designed to work in both the 850 and 1300 nm wavelength windows.
• BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
• Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
• Jacket Color: Aqua for OM3 multimode per TIA 598
• Boot Color: White
• Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M added for lengths > 30 meters.
• Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310 nm @ 23°C as tested in accordance with EIA 455-46.
• Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg

Services

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HP 15 m Multimode OM3 LC/LC Optical Cable (AJ837A)

Cabling

Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of up to 300 m;

Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m

Notes

Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um fiber optic cable and Ethernet assembly with LC duplex connectors on one end and LC duplex connectors on other end.

• Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um Coating diameter: 245 ± 10um
• Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km @850/1300nm.
• Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm. VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for Gigabit Ethernet compliant links.
• CABLE: The cable is duplex zipcord graded index 50/125um multimode optical fiber. The cable is designed to work in both the 850 and 1300 nm wavelength windows.
• BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
• Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
• Jacket Color: Aqua for OM3 multimode per TIA 598
• Boot Color: White
• Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M added for lengths > 30 meters.
• Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310 nm @ 23°C as tested in accordance with EIA 455-46.
• Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg

Services

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HP 30 m Multimode OM3 LC/LC Optical Cable (AJ838A)

Cabling

Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of up to 300 m;

Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m

Notes

Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um fiber optic cable and Ethernet assembly with LC duplex connectors on one end and LC duplex connectors on other end.

• Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um Coating diameter: 245 ± 10um
• Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km @850/1300nm.
• Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm. VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for Gigabit Ethernet compliant links.
• CABLE: The cable is duplex zipcord graded index 50/125um multimode optical fiber. The cable is designed to work in both the 850 and 1300 nm wavelength windows.
• BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
• Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
• Jacket Color: Aqua for OM3 multimode per TIA 598
• Boot Color: White
• Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M added for lengths > 30 meters.
• Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310 nm @ 23°C as tested in accordance with EIA 455-46.
• Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg

Services

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HP 50 m Multimode OM3 LC/LC Optical Cable (AJ839A)

Cabling

Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of up to 300 m;

Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m

Notes

Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um fiber optic cable and Ethernet assembly with LC duplex connectors on one end and LC duplex connectors on other end.

• Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um Coating diameter: 245 ± 10um
• Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km @850/1300nm.
• Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm. VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for Gigabit Ethernet compliant links.
• CABLE: The cable is duplex zipcord graded index 50/125um multimode optical fiber. The cable is designed to work in both the 850 and 1300 nm wavelength windows.
• BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
• Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
• Jacket Color: Aqua for OM3 multimode per TIA 598
• Boot Color: White
• Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M added for lengths > 30 meters.
• Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310 nm @ 23°C as tested in accordance with EIA 455-46.
• Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg

Services

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.