Главная Справочники HPE Managed Switches

HP 6200 Switch Series: технические характеристики и документация

Нужна помощь с конфигурацией?

Пришлите SKU, спецификацию или список требований. Специалист Apltech проверит совместимость компонентов и найдёт актуальные артикулы

Получить консультацию →

HP 6200 Switch Series: технические характеристики и документация

В архиве

HP 6200 yl Switch Series

Overview

HP 6200 yl Switch Series (Retired)

Models
HP 6200-24G-mGBIC yl Switch	J8992A

Introduction

The HP 6200-24G-mGBIC yl Switch is an advanced Layer 3 stackable switch in 1U height. It has 24 mini-GBIC slots and an expansion slot for an optional 4-port 10GbE module.

Designed to be deployed as an aggregator of traffic from the edge to the core of the network, this switch supports a variety of Gigabit mini-GBICs, such as SX, LX, LH, and 1000BASE-T. The foundation for this switch is a purpose-built ProVision ASIC that allows the most demanding networking features, such as quality of service (QoS) and security, to be implemented in a scalable yet granular fashion. With its high-performance architecture, 10GbE capability, and programmable ASIC, this switch offers excellent investment protection, flexibility, and scalability.

Key features

Distribution layer
Layer 2 to 4 and intelligent edge feature set
High performance
Low-cost mini-GBIC connectivity
10GbE uplinks

Features and Benefits

Software-defined networking

NEW OpenFlow
supports OpenFlow 1.0 and 1.3 specifications to enable SDN by allowing separation of the data (packet forwarding) and control (routing decision) paths

Quality of Service (QoS)

Advanced classifier-based QoS
classifies traffic using multiple match criteria based on Layer 2, 3, and 4 information; applies QoS policies such as setting priority level and rate limit to selected traffic on a per-port or per-VLAN basis
Layer 4 prioritization
enables prioritization based on TCP/UDP port numbers
Traffic prioritization
allows real-time traffic classification into eight priority levels mapped to eight queues
Bandwidth shaping:
- Port-based rate limiting
  provides per-port ingress/egress enforced maximum bandwidth
- Classifier-based rate limiting
  uses access control list (ACL) to enforce maximum bandwidth for ingress traffic on each port
- Reduced bandwidth
  provides per-port, per-queue egress-based reduced bandwidth
Class of Service (CoS)
sets the IEEE 802.1p priority tag based on IP address, IP Type of Service (ToS), Layer 3 protocol, TCP/UDP port number, source port, and DiffServ

Management

Remote intelligent mirroring
mirrors selected ingress/egress traffic based on ACL, port, MAC address, or VLAN to a local or remote HP 8200 zl, 6600, 6200 yl, 5400 zl, or 3500 Switch located anywhere on the network
RMON, XRMON, and sFlow
provide advanced monitoring and reporting capabilities for statistics, history, alarms, and events
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
advertises and receives management information from adjacent devices on a network, facilitating easy mapping by network management applications
Command authorization
leverages RADIUS to link a custom list of CLI commands to an individual network administrator's login; an audit trail documents activity
Friendly port names
allow assignment of descriptive names to ports
Dual flash images
provide independent primary and secondary operating system files for backup while upgrading
Multiple configuration files
can be stored to the flash image
Uni-Directional Link Detection (UDLD)
monitors a cable between two switches and shuts down the ports on both ends if the cable is broken, turning the bidirectional link into a unidirectional one; this prevents network problems such as loops
Management simplicity
provides common software features and CLI implementation across all ProVision-based switches (including the zl and yl switches)
Comware-compatible CLI:
- Comware-compatible CLI
  bridges the experience of HP Comware CLI users who are using the HP ProVision software CLI
- Display and fundamental Comware CLI commands
  are embedded in the switch CLI as native commands; display output is formatted as on Comware-based switches, and fundamental commands provide a Comware-familiar initial switch setup
- Configuration Comware CLI commands
  when Comware commands are entered, CLI help is elicited to formulate the correct ProVision software CLI command

Connectivity

Jumbo frames
on Gigabit Ethernet and 10-Gigabit Ethernet ports, jumbo frames allow high-performance remote backup and disaster-recovery services
IPv6:
- IPv6 host
  enables switches to be managed in an IPv6 network
- Dual stack (IPv4 and IPv6)
  transitions from IPv4 to IPv6, supporting connectivity for both protocols
- MLD snooping
  forwards IPv6 multicast traffic to the appropriate interface
- IPv6 ACL/QoS
  supports ACL and QoS for IPv6 network traffic
- IPv6 routing
  supports static and OSPFv3 routing protocols
- 6in4 tunneling
  supports encapsulation of IPv6 traffic in IPv4 packets

Performance

High-speed/capacity architecture
105.6 Gbps crossbar switching fabric provides intramodule and intermodule switching with 75.7 million pps throughput on the purpose-built ProVision ASICs
Selectable queue configurations
allows for increased performance by selecting the number of queues and associated memory buffering that best meet the requirements of the network applications

Resiliency and high availability

NEW Virtual Router Redundancy Protocol (VRRP)
allows groups of two routers to dynamically back each other up to create highly available routed environments in IPv4 and IPv6 networks
IEEE 802.1s Multiple Spanning Tree Protocol
provides high link availability in multiple VLAN environments by allowing multiple spanning trees; encompasses IEEE 802.1D Spanning Tree Protocol and IEEE 802.1w Rapid Spanning Tree Protocol
IEEE 802.3ad Link Aggregation Control Protocol (LACP) and HP port trunking
support up to 144 trunks, each with up to eight links (ports) per trunk
Distributed trunking
enables loop-free and redundant network topology without using Spanning Tree Protocol; allows a server or switch to connect to two switches using one logical trunk for redundancy and load sharing
Uplink Failure Detection
provides active-standby network path redundancy for servers that are configured for active-standby NIC teaming
NEW SmartLink
provides easy-to-configure link redundancy of active and standby links

Layer 2 switching

IEEE 802.1ad Q-in-Q
increases the scalability of an Ethernet network by providing a hierarchical structure; connects multiple LANs on a high-speed campus or metro network
HP switch meshing
dynamically load balances across multiple active redundant links to increase available aggregate bandwidth
VLAN support and tagging
supports complete IEEE 802.1Q standard and 2,048 VLANs simultaneously
IEEE 802.1v protocol VLANs
isolate select non-IPv4 protocols automatically into their own VLANs
GARP VLAN Registration Protocol
allows automatic learning and dynamic assignment of VLANs
Rapid Per-VLAN Spanning Tree (RPVST+)
allows each VLAN to build a separate spanning tree to improve link bandwidth usage; is compatible with PVST+

Layer 3 services

User Datagram Protocol (UDP) helper function
allows UDP broadcasts to be directed across router interfaces to specific IP unicast or subnet broadcast addresses and prevents server spoofing for UDP services such as DHCP
Loopback interface address
defines an address in Routing Information Protocol (RIP) and Open Standard Path First (OSPF), improving diagnostic capability
Route map
provide more control during route redistribution; allow filtering and altering of route metrics

Layer 3 routing

Static IP routing
provides manually configured routing for both IPv4 and IPv6 networks
Routing Information Protocol (RIP)
provides RIPv1 and RIPv2 routing
OSPF
provides OSPFv2 for IPv4 routing and OSPFv3 for IPv6 routing
Border Gateway Protocol (BGP)
provides IPv4 Border Gateway Protocol routing, which is scalable, robust, and flexible

Security

Switch CPU protection
provides automatic protection against malicious network traffic trying to shut down the switch
Virus throttling
detects traffic patterns typical of WORM-type viruses and either throttles or entirely prevents the virus from spreading across the routed VLANs without requiring external appliances
ICMP throttling
defeats ICMP denial-of-service attacks by enabling any switch port to automatically throttle ICMP traffic
Multiple user authentication methods:
- IEEE 802.1X users per port: provides authentication of multiple IEEE 802.1X users per port; prevents user "piggybacking" on another user's IEEE 802.1X authentication
- Web-based authentication: authenticates from Web browser for clients that do not support IEEE 802.1X supplicant; customized remediation can be processed on an external Web server
- MAC-based authentication: client is authenticated with the RADIUS server based on client's MAC address
- Concurrent IEEE 802.1X, Web, and MAC authentication schemes per port: switch port will accept up to 32 sessions of IEEE 802.1X, Web, and MAC authentications
Access control lists (ACLs)
provide filtering based on the IP field, source/destination IP address/subnet, and source/destination TCP/UDP port number on a per-VLAN or per-port basis
Identity-driven ACL
enables implementation of a highly granular and flexible access security policy and VLAN assignment specific to each authenticated network user
DHCP protection
blocks DHCP packets from unauthorized DHCP servers, preventing denial-of-service attacks
STP BPDU port protection
blocks Bridge Protocol Data Units (BPDUs) on ports that do not require BPDUs, preventing forged BPDU attacks
Dynamic IP lockdown
works with DHCP protection to block traffic from unauthorized hosts, preventing IP source address spoofing
Dynamic ARP protection
blocks ARP broadcasts from unauthorized hosts, preventing eavesdropping or theft of network data
Detection of malicious attacks
monitors 10 types of network traffic and sends a warning when an anomaly that potentially can be caused by malicious attacks is detected
Port security
allows access only to specified MAC addresses, which can be learned or specified by the administrator
MAC address lockout
prevents particular configured MAC addresses from connecting to the network
Source-port filtering
allows only specified ports to communicate with each other
RADIUS/TACACS+
eases switch management security administration by using a password authentication server
Secure Shell
encrypts all transmitted data for secure remote CLI access over IP networks
Secure Sockets Layer (SSL)
encrypts all HTTP traffic, allowing secure access to the browser-based management GUI in the switch
Secure FTP
allows secure file transfer to and from the switch; protects against unwanted file downloads or unauthorized copying of a switch configuration file
Management Interface Wizard
helps secure management interfaces such as SNMP, telnet, SSH, SSL, Web, and USB at the desired level
Secure management access
securely encrypts all access methods (CLI, GUI, or MIB) through SSHv2, SSL, and/or SNMPv3
Switch management logon security
can require either RADIUS or TACACS+ authentication for secure switch CLI logon
Security banner: displays customized security policy when users log in to the switch
USB Secure Autorun (requires HP PCM+)
deploys, diagnoses, and updates a switch using a USB flash drive; works with a secure credential to prevent tampering
STP Root Guard
protects the root bridge from malicious attacks or configuration mistakes

Convergence

IP multicast routing
includes PIM Sparse and Dense modes to route IP multicast traffic
IP multicast snooping (data-driven IGMP)
automatically prevents flooding of IP multicast traffic
LLDP-MED (Media Endpoint Discovery)
is a standard extension of LLDP that stores values for parameters such as QoS and VLAN to automatically configure network devices such as IP phones
Auto VLAN configuration for voice:
- RADIUS VLAN: uses a standard RADIUS attribute and LLDP-MED to automatically configure a VLAN for IP phones
- CDPv2: uses CDPv2 to configure legacy IP phones
NEW Local MAC Authentication
assigns attributes such as VLAN and QoS using locally configured profile that can be a list of MAC prefixes

Warranty and support

Lifetime Warranty 2.0
advance hardware replacement for as long as you own the product with next-business-day delivery (available in most countries)†
Electronic and telephone support (for Lifetime Warranty 2.0)
limited 24x7 telephone support is available from HP for the first 3 years; limited electronic and business hours telephone support is available from HP for the entire warranty period; to reach our support centers, refer to http://www.hp.com/networking/contact-support; for details on the duration of support provided with your product purchase, refer to www.hp.com/networking/warrantysummary
Software releases
to find software for your product, refer to http://www.hp.com/networking/support; for details on the software
releases available with your product purchase, refer to www.hp.com/networking/warrantysummary

†HP warranty includes repair or replacement of hardware for as long as you own the product, with next business day advance replacement (available in most countries). The disk drive included with HP AllianceOne Advanced Services and Services zl Modules, HP Threat Management Services zl Module, HP AllianceOne Extended zl Module with Riverbed Steelhead, HP MSM765zl Mobility Controller and HP Survivable Branch Communication zl Module powered by Microsoft Lync has a five-year hardware warranty. For details, refer to the Software license and hardware warranty statements at http://www.hp.com/networking/warranty.

Configuration

Build To Order: BTO is a standalone unit with no integration. BTO products ship standalone are not part of a CTO or Rack-Shippable solution.

HP 6200-24G-mGBIC yl Switch		J8992A
24 open mini-GBIC (SFP) slots min=0 \ max=24 SFP Transceivers 1U - Height		See Configuration Note:1, 2

PDU Cable NA/MEX/TW/JP		J8992A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)

PDU Cable ROW		J8992A#B2C
C15 PDU Jumper Cord (ROW)

Configuration Rules:

Note 1	The following Transceivers install into this switch:
	HP X121 1G SFP LC SX Transceiver	J4858C
	HP X121 1G SFP LC LX Transceiver	J4859C
	HP X111 100M SFP LC FX Transceiver	J9054C
	HP X121 1G SFP RJ45 T Transceiver	J8177C
	HP X112 100M SFP LC BX-D Transceiver	J9099B
	HP X112 100M SFP LC BX-U Transceiver	J9100B
	HP X121 1G SFP LC LH Transceiver	J4860C
	HP X122 1G SFP LC BX-D Transceiver	J9142B
	HP X122 1G SFP LC BX-U Transceiver	J9143A
	HP X131 10G X2 SC ER Transceiver	J8438A
	HP X131 10G X2 SC SR Transceiver	J8436A
	HP X131 10G X2 SC LR Transceiver	J8437A
	HP X131 10G X2 SC LRM Transceiver	J9144A

Note 2	Localization required on orders without #B2B or #B2C options.

Remarks:
	Drop down under power supply should offer the following options and results: Switch/Router/Power Supply to PDU Power Cord - #B2B in North America, Mexico, Taiwan, and Japan or #B2C ROW. (Watson Default B2B or B2C for Rack Level CTO) Switch/Router/Power Supply to Wall Power Cord - Localized Option (Watson Default for BTO and Box Level CTO)

Factory Racked Models

HP 6200-24G-mGBIC yl Switch		J8992A
24 open mini-GBIC (SFP) slots min=0 \ max=24 SFP Transceivers 1U - Height		See Configuration Note:1, 2

Configuration Rules:

Note 1	The following Transceivers install into this switch:
	HP X121 1G SFP LC SX Transceiver	J4858C
	HP X121 1G SFP LC LX Transceiver	J4859C
	HP X111 100M SFP LC FX Transceiver	J9054C
	HP X121 1G SFP RJ45 T Transceiver	J8177C
	HP X112 100M SFP LC BX-D Transceiver	J9099B
	HP X112 100M SFP LC BX-U Transceiver	J9100B
	HP X121 1G SFP LC LH Transceiver	J4860C
	HP X122 1G SFP LC BX-D Transceiver	J9142B
	HP X122 1G SFP LC BX-U Transceiver	J9143A
	HP X131 10G X2 SC ER Transceiver	J8438A
	HP X131 10G X2 SC SR Transceiver	J8436A
	HP X131 10G X2 SC LR Transceiver	J8437A
	HP X131 10G X2 SC LRM Transceiver	J9144A

Note 2	If this switch is factory installed in HP Universal Racks, Then the J9583A#0D1 is required. AMS then J9583A#0D1is required. EMEA then J9583A#0D1 is required. APD, Japan and China then J9583A#0D1 is required. CLIC Only - Allow the J9583AZ in all regions.

Enter the following menu selections as integrated to the CTO Model X server above if order is factory built.

Modules

System (std 0 // max=2) User Selection (min 0 / max=2) per Chassis

HP 10GbE 2-port SFP+/2-port CX4 yl Mod		J9312A
min=0 \ max=2 SFP Transceivers		See Configuration Note:1

HP 10GbE 2-port X2 / 2-port CX4 yl Module		J8694A

Configuration Rules:

Note 1	The following Transceivers install into this switch:
	HP X121 1G SFP LC SX Transceiver	J4858C
	HP X121 1G SFP LC LX Transceiver	J4859C
	HP X111 100M SFP LC FX Transceiver	J9054C
	HP X121 1G SFP RJ45 T Transceiver	J8177C
	HP X112 100M SFP LC BX-D Transceiver	J9099B
	HP X112 100M SFP LC BX-U Transceiver	J9100B
	HP X121 1G SFP LC LH Transceiver	J4860C
	HP X122 1G SFP LC BX-D Transceiver	J9142B
	HP X122 1G SFP LC BX-U Transceiver	J9143A
	HP X131 10G X2 SC ER Transceiver	J8438A
	HP X131 10G X2 SC SR Transceiver	J8436A
	HP X131 10G X2 SC LR Transceiver	J8437A
	HP X131 10G X2 SC LRM Transceiver	J9144A

Transceivers

SFP Transceivers

HP X121 1G SFP LC SX Transceiver		J4858C
HP X121 1G SFP LC LX Transceiver		J4859C
HP X111 100M SFP LC FX Transceiver		J9054C
HP X121 1G SFP LC LH Transceiver		J4860C
HP X121 1G SFP RJ45 T Transceiver		J8177C
HP X122 1G SFP LC BX-D Transceiver		J9142B
HP X122 1G SFP LC BX-U Transceiver		J9143B
HP X112 100M SFP LC BX-D Transceiver		J9099B
HP X112 100M SFP LC BX-U Transceiver		J9100B
HP X131 10G X2 SC ER Transceiver		J8438A
HP X131 10G X2 SC SR Transceiver		J8436A
HP X131 10G X2 SC LR Transceiver		J8437A
HP X131 10G X2 SC LRM Transceiver		J9144A

Cables

Multi-Mode Cables

HP .5m Multi-mode OM3 LC/LC FC Cable		AJ833A
HP 1m Multi-mode OM3 LC/LC FC Cable		AJ834A
HP 2 m Multimode OM3 LC/LC FC Cable		AJ835A
HP 5 m Multimode OM3 LC/LC FC Cable		AJ836A
HP 15 m Multimode OM3 LC/LC FC Cable		AJ837A
HP 30 m Multimode OM3 LC/LC FC Cable		AJ838A
HP 50 m Multimode OM3 LC/LC FC Cable		AJ839A
HP Premier Flex LC/LC OM4 2f 1m Cbl		QK732A
HP Premier Flex LC/LC OM4 2f 2m Cbl		QK733A
HP Premier Flex LC/LC OM4 2f 5m Cbl		QK734A
HP Premier Flex LC/LC OM4 2f 15m Cbl		QK735A
HP Premier Flex LC/LC OM4 2f 30m Cbl		QK736A
HP Premier Flex LC/LC OM4 2f 50m Cbl		QK737A

Switch Options

Rack Mount kits

HP X410 1U Univ 4-post Rack Mnt Kit		J9583A
		See Configuration Note:1, 2

Rack Shelf		AB469A
		See Configuration Note:3

Configuration Rules:

Note 1	Default with switch.

Note 2	If this Mounting Kit is order with #0D1 then it integrates to the HP Universal Rack. (not the switch)

Note 3	This has existing rules that say 1 per 20 if 1U and 1 per 10 if its 3U or more. This rule is fine for ProCurve. Note: Both parts above are required to ship the 62xx Series Switches installed in a rack. Exceptions- The Shelf Kit (AB469A) may be removed if the Switch is supported underneath by a full depth Server of 3U height or greater mounted on fixed rails

Technical Specifications

HP 6200-24G-mGBIC yl Switch (J8992A)	I/O ports and slots	24 open mini-GBIC (SFP) slots Supports a maximum of 4 10-GbE ports, with optional module
	Physical characteristics	Dimensions	17.44(w) x 15.43(d) x 1.73(h) in (44.3 x 39.2 x 4.4 cm) (1U height)
	Physical characteristics	Weight	14.11 lb (6.4 kg)
	Memory and processor	Processor	Freescale PowerPC 8540 @ 666 MHz, 4 MB flash, 256 MB DDR SDRAM
	Mounting and enclosure	Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included); horizontal surface mounting only
	Performance	1000 Mb Latency	< 3.7 µs (FIFO 64-byte packets)
		10 Gbps Latency	< 2.1 µs (FIFO 64-byte packets)
		Throughput	up to 75.7 million pps
		Routing/Switching capacity	101.8 Gb/s
		Switch fabric speed	105.6 Gb/s
		Routing table size	10000 entries (IPv4)
	Environment	Operating temperature	32ºF to 131ºF (0ºC to 55ºC); 32°F to 104°F (40°C) when used with any X2 10-GbE
		Operating relative humidity	15% to 95% @ 104ºF (40ºC), noncondensing
		Non-operating/ Storage temperature	–40°F to 158°F (-40°C to 70°C)
		Non-operating/ Storage relative humidity	15% to 95% at 149°F (65°C), noncondensing
		Altitude	up to 15,000 ft (4.6 km)
		Acoustic	Power: 55.1 dB; DIN 45635T.19 per ISO 7779
	Electrical characteristics	Description	The switch automatically adjusts to any voltage between 100-127 and 200-240 V with either 50 or 60 Hz.
		Maximum heat dissipation	829 BTU/hr (875 kJ/hr)
		AC v oltage	100-127/200-240 VAC
		Current	1.8/0.9 A
		Power consumption	243 W
		Frequency	50/60 Hz
	Safety	CSA 22.2 No. 60950; UL 60950; IEC 60950; EN 60950
	Emissions	FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A
	Immunity	EN	EN 55024, CISPR 24
		ESD	IEC 61000-4-2; 4 kV CD, 8 kV AD
		Radiated	IEC 61000-4-3; 3 V/m
		EFT/Burst	IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line)
		Surge	IEC 61000-4-5; 1 kV/2 kV AC
		Conducted	IEC 61000-4-6; 3 V
		Power frequency magnetic field	IEC 61000-4-8; 1 A/m, 50 or 60 Hz
		Voltage dips and interruptions	IEC 61000-4-11; >95% reduction, 0.5 period; 30% reduction, 25 periods
		Harmonics	EN 61000-3-2, IEC 61000-3-2
		Flicker	EN 61000-3-3, IEC 61000-3-3
	Management	HP PCM+; HP PCM (included); command-line interface; Web browser; configuration menu; out-of-band management (serial RS-232C)
	Notes	Supported 1G SFP transceivers are revision "B" or later (product number ends with the letter "B" or later; for example, J9142B, J8177C).
	Services	3-year, 4-hour onsite, 13x5 coverage for hardware (U2855E) 3-year, 4-hour onsite, 24x7 coverage for hardware (U2856E) 3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 SW phone support and SW updates (U6304E) 3-year, 24x7 SW phone support, software updates (UE262E) 1-year, post-warranty, 4-hour onsite, 13x5 coverage for hardware (HR889E) 1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware (HR890E) 1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support (HR891E) Installation with minimum configuration, system-based pricing (U4826E) Installation with HP-provided configuration, system-based pricing (U4830E) 4-year, 4-hour onsite, 13x5 coverage for hardware (UR868E) 4-year, 4-hour onsite, 24x7 coverage for hardware (UR869E) 4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (UR870E) 4-year, 24x7 SW phone support, software updates (UR871E) 5-year, 4-hour onsite, 13x5 coverage for hardware (UR872E) 5-year, 4-hour onsite, 24x7 coverage for hardware (UR873E) 5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (UR874E) 5-year, 24x7 SW phone support, software updates (UR875E) 3 Yr 6 hr Call-to-Repair Onsite (UW356E) 4 Yr 6 hr Call-to-Repair Onsite (UW357E) 5 Yr 6 hr Call-to-Repair Onsite (UW358E) 1-year, 6 hour Call-To-Repair Onsite for hardware (HR893E) 1-year, 24x7 software phone support, software updates (HR892E) 1-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange (HS610E) 1-year, 24x7 software phone support, software updates + 4 hour hardware exchange (HS611E) 3-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange (HS612E) 3-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HS613E) 4-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange (HS614E) 4-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HS615E) 5-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange (HS616E) 5-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HS617E) Refer to the HP website at www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.
	Standards and protocols	BGP	RFC 1997 BGP Communities Attribute RFC 2918 Route Refresh Capability RFC 4271 A Border Gateway Protocol 4 (BGP-4) RFC 4456 BGP Route Reflection: An Alternative to Full Mesh Internal BGP (IBGP) RFC 5492 Capabilities Advertisement with BGP-4
		Device Management	RFC 1591 DNS (client) HTML and telnet management
		General Protocols	IEEE 802.1ad Q-in-Q IEEE 802.1AX-2008 Link Aggregation IEEE 802.1D MAC Bridges IEEE 802.1p Priority IEEE 802.1Q VLANs IEEE 802.1s Multiple Spanning Trees IEEE 802.1v VLAN classification by Protocol and Port IEEE 802.1w Rapid Reconfiguration of Spanning Tree IEEE 802.3ad Link Aggregation Control Protocol (LACP) IEEE 802.3x Flow Control RFC 768 UDP RFC 783 TFTP Protocol (revision 2) RFC 792 ICMP RFC 793 TCP RFC 826 ARP RFC 854 TELNET RFC 868 Time Protocol RFC 951 BOOTP RFC 1058 RIPv1 RFC 1350 TFTP Protocol (revision 2) RFC 1519 CIDR RFC 1542 BOOTP Extensions RFC 2030 Simple Network Time Protocol (SNTP) v4 RFC 2131 DHCP RFC 2453 RIPv2 RFC 2548 (MS-RAS-Vendor only) RFC 3046 DHCP Relay Agent Information Option RFC 3576 Ext to RADIUS (CoA only) RFC 3768 VRRP RFC 4675 RADIUS VLAN & Priority UDLD (Uni-directional Link Detection)
		IP Multicast	RFC 3376 IGMPv3 (host joins only) RFC 3973 PIM Dense Mode RFC 4601 PIM Sparse Mode
		IPv6	RFC 1981 IPv6 Path MTU Discovery RFC 2375 IPv6 Multicast Address Assignments RFC 2460 IPv6 Specification RFC 2464 Transmission of IPv6 over Ethernet Networks RFC 2710 Multicast Listener Discovery (MLD) for IPv6 RFC 2925 Definitions of Managed Objects for Remote Ping, Traceroute, and Lookup Operations (Ping only) RFC 3019 MLDv1 MIB RFC 3315 DHCPv6 (client and relay) RFC 3484 Default Address Selection for IPv6 RFC 3587 IPv6 Global Unicast Address Format RFC 3596 DNS Extension for IPv6 RFC 3810 MLDv2 for IPv6 RFC 3810 Multicast Listener Discovery Version 2 (MLDv2) for IPv6 RFC 4022 MIB for TCP RFC 4087 IP Tunnel MIB RFC 4113 MIB for UDP RFC 4213 Basic Transition Mechanisms for IPv6 Hosts and Routers RFC 4251 SSHv6 Architecture RFC 4252 SSHv6 Authentication RFC 4253 SSHv6 Transport Layer RFC 4254 SSHv6 Connection RFC 4291 IP Version 6 Addressing Architecture RFC 4293 MIB for IP RFC 4294 IPv6 Node Requirements RFC 4419 Key Exchange for SSH RFC 4443 ICMPv6 RFC 4541 IGMP & MLD Snooping Switch RFC 4861 IPv6 Neighbor Discovery RFC 4862 IPv6 Stateless Address Auto-configuration RFC 5095 Deprecation of Type 0 Routing Headers in IPv6 RFC 5340 OSPF for IPv6 RFC 5453 Reserved IPv6 Interface Identifiers RFC 5519 Multicast Group Membership Discovery MIB (MLDv2 only) RFC 5722 Handling of Overlapping IPv6 Fragments
		MIBs	IEEE 802.1ap (MSTP and STP MIB's only) RFC 1213 MIB II RFC 1493 Bridge MIB RFC 1724 RIPv2 MIB RFC 1850 OSPFv2 MIB RFC 2021 RMONv2 MIB RFC 2096 IP Forwarding Table MIB RFC 2613 SMON MIB RFC 2618 RADIUS Client MIB RFC 2620 RADIUS Accounting MIB RFC 2665 Ethernet-Like-MIB RFC 2668 802.3 MAU MIB RFC 2674 802.1p and IEEE 802.1Q Bridge MIB RFC 2737 Entity MIB (Version 2) RFC 2787 VRRP MIB RFC 2863 The Interfaces Group MIB RFC 2925 Ping MIB RFC 2933 IGMP MIB
		Network Management	IEEE 802.1AB Link Layer Discovery Protocol (LLDP) RFC 2819 Four groups of RMON: 1 (statistics), 2 (history), 3 (alarm) and 9 (events) RFC 3176 sFlow ANSI/TIA-1057 LLDP Media Endpoint Discovery (LLDP-MED) SNMPv1/v2c/v3 XRMON
		OSPF	RFC 2328 OSPFv2 RFC 3101 OSPF NSSA RFC 5340 OSPF for IPv6
		QoS/Cos	RFC 2474 DiffServ Precedence, including 8 queues/port RFC 2597 DiffServ Assured Forwarding (AF) RFC 2598 DiffServ Expedited Forwarding (EF)
		Security	IEEE 802.1X Port Based Network Access Control RFC 1492 TACACS+ RFC 2865 RADIUS (client only) RFC 2866 RADIUS Accounting RFC 3579 RADIUS Support For Extensible Authentication Protocol (EAP) Secure Sockets Layer (SSL) SSHv2 Secure Shell

Accessories

HP 6200 yl Switch Series accessories
HP 6200-24G-mGBIC yl Switch (J8992A)
HP 10GbE 2-port SFP+ / 2-port CX4 yl Module	J9312A
HP 10GbE 2-port X2 / 2-port CX4 yl Module	J8694A
HP X131 10G X2 SC ER Transceiver	J8438A
HP X131 10G X2 SC SR Transceiver	J8436A
HP X131 10G X2 CX4 Transceiver	J8440C
HP X111 100M SFP LC FX Transceiver	J9054C
HP X131 10G X2 SC LR Transceiver	J8437A
HP X131 10G X2 SC LRM Transceiver	J9144A
HP X112 100M SFP LC BX-D Transceiver	J9099B
HP X112 100M SFP LC BX-U Transceiver	J9100B
HP X121 1G SFP LC LH Transceiver	J4860C
HP X121 1G SFP LC SX Transceiver	J4858C
HP X121 1G SFP LC LX Transceiver	J4859C
HP X121 1G SFP RJ45 T Transceiver	J8177C
HP X122 1G SFP LC BX-D Transceiver	J9142B
HP X122 1G SFP LC BX-U Transceiver	J9143B
HP LC to LC Multi-mode OM3 2-Fiber 0.5m 1-Pack Fiber Optic Cable	AJ833A
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 1m Cable	QK732A
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 2m Cable	QK733A
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 5m Cable	QK734A
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 15m Cable	QK735A
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 30m Cable	QK736A
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 50m Cable	QK737A
HP 620 Redundant/External Power Supply	J8696A

Accessory Product Details

HP 10GbE 2-port X2/2-port CX4 yl Module (J8694A)	Ports	2 open 10-GbE X2 transceiver slots 2 10-GbE ports (IEEE 802.3ak Type 10GBASE-CX4); Duplex: full only
	Physical characteristics	Dimensions	7.76(d) x 7.52(w) x 14.29(h) in. (19.7 x 19.1 x 36.3 cm)
		Weight	1.54 lb. (0.7 kg)
	Environment	Operating temperature	32°F to 131°F (0°C to 55°C)
		Operating relative humidity	15% to 95%, noncondensing
		Nonoperating/Storage temperature	-40°F to 158°F (-40°C to 70°C)
		Nonoperating/Storage relative humidity	15% to 90%, noncondensing
	Cabling	Maximum distance: • CX4: 15 m using CX4 cable or 300 m using media converter with ribbon MMF
	Notes	Operating temperature is 32°F to 104°F (0°C to 40°C) if any X2 10-GbE optic or transceiver is inserted in any X2 slot. One 0.5 m CX4 cable is included.
	Services	Refer to the HP website at: http://www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

HP 10GbE 2-port SFP+/2-port CX4 yl Module (J9312A)	Ports	2 SFP+ 10-GbE ports (IEEE 802.3ae Type 10GBASE-LR); Duplex: full only 2 CX4 10-GbE ports (IEEE 802.3ak Type 10GBASE-CX4); Duplex: full only
	Physical characteristics	Dimensions	7.76(d) x 7.52(w) x 14.29(h) in. (19.7 x 19.1 x 36.3 cm)
		Weight	1.45 lb. (0.66 kg)
	Environment	Operating temperature	32°F to 131°F (0°C to 55°C)
		Operating relative humidity	15% to 95%, noncondensing
		Nonoperating/Storage temperature	-40°F to 158°F (-40°C to 70°C)
		Nonoperating/Storage relative humidity	15% to 90%, noncondensing
	Cabling	Maximum distance: • CX4: 15 m using CX4 cable or 300 m using media converter with ribbon MMF
	Notes	Operating temperature is 32°F to 104°F (0°C to 40°C) if any SFP+ 10-GbE optic or transceiver is inserted in any SFP+ slot. One 0.5 m CX4 cable is included.
	Services	Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

HP 620 Redundant/External Power Supply (J8696A)	Ports	2 redundant power supply ports Restrictions: 195 W available per port 2 external power supply ports Restrictions: 398 W available per port
	Physical characteristics	Dimensions	15.4(d) x 17.4(w) x 1.73(h) in. (39.12 x 44.2 x 4.39 cm) (1U height)
	Physical characteristics	Weight	15.2 lb. (6.89 kg)
	Mounting	Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included); horizontal surface mounting only
	Environment	Operating temperature	32°F to 131°F (0°C to 55°C)
		Operating relative humidity	15% to 95% @ 104°F (40°C), noncondensing
		Nonoperating/Storage temperature	-40°F to 158°F (-40°C to 70°C)
		Nonoperating/Storage relative humidity	15% to 90% @ 149°F (65°C), noncondensing
		Altitude	up to 10,000 ft. (3 km)
		Acoustic	LwA per ISO 7779: 54.2 dB
	Electrical characteristics	Maximum heat dissipation	400 BTU/hr (422 kJ/hr), for the actual 620 itself. PoE-powered device heat dissipation assumed to be outside the 620.
		Voltage	100-127/200-240 VAC
		Current	16/8 A
		Maximum power rating	1440 W
		RPS power	390 W
		PoE power	796 W
		RPS	12 V
		PoE	-50 V
		Frequency	50/60 Hz
		Notes	Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated. Above figures are for maximum RPS and PoE power being supplied to two switches simultaneously. 200 - 240 V power cords shipped with the 620 have a wall plug rated as close to 13 A as specific country standards allow.
	Safety	CSA 22.2 No. 60950; EN 60950/IEC 60950; UL 60950
	Emissions	FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A
	Immunity	EN	EN 55024, CISPR 24
		ESD	IEC 61000-4-2
		Radiated	IEC 61000-4-3
		EFT/Burst	IEC 61000-4-4
		Surge	IEC 61000-4-5
		Conducted	IEC 61000-4-6
		Power frequency magnetic field	IEC 61000-4-8
		Voltage dips and interruptions	IEC 61000-4-11
		Harmonics	EN 61000-3-2, IEC 61000-3-2
		Flicker	EN 61000-3-3, IEC 61000-3-3
	Management	Unmanaged power supply; provides information via LEDs (LEDs repeated on front and back panel) or through port interfaces of attached devices
	Notes	The 620 supports the HP Switch 2900 Series (RPS) and 3500yl Series (RPS/PoE), as well as 6200yl (RPS) switches. The HP Switch 5400zl Series is not supported. The 620 includes four 2 m RPS/EPS cables. These cables can be used to carry either RPS or PoE power to the switch being powered.
	Services	3-year, 4-hour onsite, 13x5 coverage for hardware (U9270E) 3-year, 4-hour onsite, 24x7 coverage for hardware (U9271E) 4-year, 4-hour onsite, 13x5 coverage for hardware (UR854E) 4-year, 4-hour onsite, 24x7 coverage for hardware (UR855E) 5-year, 4-hour onsite, 13x5 coverage for hardware (UR857E) 5-year, 4-hour onsite, 24x7 coverage for hardware (UR858E) 3 Yr 6 hr Call-to-Repair Onsite (UW371E) 4 Yr 6 hr Call-to-Repair Onsite (UW372E) 5 Yr 6 hr Call-to-Repair Onsite (UW373E) Refer to the HP website at: http://www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

HP X131 10G X2 SC ER Transceiver (J8438A) HP X131 10G X2 SC ER Transceiver: An X2 format 10-gigabit transceiver with SC connectors using ER technology.	Ports	1 SC 10-GbE port (IEEE 802.3ae Type 10GBASE-ER); Duplex: full only
	Connectivity	Connector type	SC
		Wavelength	1550 nm
	Physical characteristics	Dimensions	3.48(d) x 1.42(w) x 0.43(h) in. (8.84 x 3.61 x 1.09 cm)
		Weight	0.35 lb. (0.16 kg)
		Transceiver form factor	X2
	Environment	Operating temperature	32ºF to 104ºF (0ºC to 40ºC)
		Operating relative humidity	15% to 95%, noncondensing
	Electrical characteristics	Power consumption typical	3 W
		Power consumption maximum	4.5 W
	Cabling	Cable type:: Low metal content, single-mode fiber-optic, complying with ITU-T G.652 and ISO/IEC 793-2 Type B1;
		Cable length	2m to 30km (max 40km on engineered links)
		Fiber type	Single Mode
	Notes	Conditioning patch cord cables are not supported For fiber patch cords, use Ultra Physical Contact (UPC) surface termination/polish. Angled Physical Contact (APC) is not recommended.
	Services	Refer to the HP website at www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

HP X131 10G X2 SC SR Transceiver (J8436A) HP X131 10G X2 SC SR Transceiver: An X2 format 10-gigabit transceiver with SC connectors using SR technology.	Ports	1 SC 10-GbE port (IEEE 802.3ae Type 10GBASE-SR); Duplex: full only
	Connectivity	Connector type	SC
	Connectivity	Wavelength	850 nm
	Physical characteristics	Dimensions	3.48(d) x 1.42(w) x 0.43(h) in. (8.84 x 3.61 x 1.09 cm)
		Weight	0.35 lb. (0.16 kg)
		Transceiver form factor	X2
	Environment	Operating temperature	32ºF to 158ºF (0ºC to 70ºC)
		Operating relative humidity	0% to 95%, noncondensing
		Nonoperating/Storage temperature	-40ºF to 185ºF (-40ºC to 85ºC)
		Nonoperating/Storage relative humidity	0% to 95%, noncondensing
		Altitude	up to 10,000 ft. (3 km)
	Electrical characteristics	Power consumption typical	1.7 W
	Electrical characteristics	Power consumption maximum	2.4 W
	Cabling	Cable type:: 62.5/125 µm or 50/125 µm (core/cladding) graded-index, low metal content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2 Type A1b or A1a, respectively; Maximum distance: 2-26m with 62.5 µm multimode cable @ 160 MHzkm 2-33m with 62.5 µm multimode cable @ 200 MHzkm 2-66m with 50 µm multimode cable @ 400 MHzkm 2-82m with 50 µm multimode cable @ 500 MHzkm 2-300m with 50 µm multimode cable @ 2000 MHz*km
		Cable length	2-300m
		Fiber type	Multi Mode
	Notes	For fiber patch cords, use Ultra Physical Contact (UPC) surface termination/polish. Angled Physical Contact (APC) is not recommended.
	Services	Refer to the HP website at http://www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

HP X131 10G X2 CX4 Transceiver (J8440C) HP X131 10G X2 CX4 Transceiver: An X2 format 10-gigabit CX4 transceiver.	Ports	1 CX4 10-GbE port (IEEE 802.3ak Type 10GBASE-CX4); Duplex: full only
	Connectivity	Connector type	CX4
	Physical characteristics	Dimensions	3.54(d) x 1.42(w) x 0.53(h) in. (8.99 x 3.61 x 1.35 cm)
		Weight	0.18 lb. (0.08 kg)
		Transceiver form factor	X2
	Environment	Operating temperature	32ºF to 131ºF (0ºC to 55ºC)
		Operating relative humidity	15% to 95%, noncondensing
		Nonoperating/Storage temperature	-40ºF to 185ºF (-40ºC to 85ºC)
		Altitude	up to 10,000 ft. (3 km)
	Electrical characteristics	Power consumption typical	1.0 W
	Electrical characteristics	Power consumption maximum	3.3 W
	Cabling	Maximum distance: • 15m with CX4 cables • 300m with optical media converter and multimode fiber cable
	Notes	Connector: CX4; Duplex: full For suggested vendors of CX4 cables, please see the "Cabling" answers on the "HP 10-GbE Transceivers" FAQs Web page.
	Services	Refer to the HP website at www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

HP X111 100M SFP LC FX Transceiver (J9054C)	Ports	1 LC 100BASE-FX port (IEEE 802.3u Type 100BASE-FX); Duplex: half or full
	Physical characteristics	Dimensions	2.7(d) x 0.54(w) x 0.48(h) in. (6.86 x 1.38 x 1.22 cm)
		Weight	0.06 lb. (0.03 kg)
	Environment	Operating temperature	32°F to 158°F (0°C to 70°C)
		Operating relative humidity	5% to 95%
		Nonoperating/Storage temperature	-40°F to 185°F (-40°C to 85°C)
		Nonoperating/Storage relative humidity	5% to 85%
		Altitude	up to 10,000 ft. (3 km)
	Cabling	Cable type: 62.5/125 ìm or 50/125 ìm (core/cladding) diameter, graded-index, low metal content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2 Type A1b or A1a, respectively; Maximum distance: • 2 km (full duplex) or 412 m (half duplex)
	Notes	Transmitter wavelength: 1310nm Power consumption is 1.1 watt maximum. For supported platforms and minimum software requirements to support this product, see the document titled "Support for the J9054C 100-FX SFP-LC Transceiver" on the "ProCurve Mini-GBICs and SFPs" Manuals Web page.
	Services	Refer to the HP website at: http://www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

HP X131 10G X2 SC LR Transceiver (J8437A) An X2 form-factor transceiver that supports the 10-Gigabit LR standard, providing 10-Gigabit connectivity up to 10 km on single-mode fiber.	Ports	1 SC 10-GbE port (IEEE 802.3ae Type 10GBASE-LR); Duplex: full only
	Connectivity	Connector type	SC
	Connectivity	Wavelength	1310 nm
	Physical characteristics	Dimensions	3.48(d) x 1.42(w) x 0.43(h) in. (8.84 x 3.61 x 1.09 cm)
		Weight	0.35 lb. (0.16 kg)
		Transceiver form factor	X2
	Environment	Operating temperature	32ºF to 104ºF (0ºC to 40ºC)
		Operating relative humidity	15% to 95%, noncondensing
		Nonoperating/Storage temperature	-40ºF to 185ºF (-40ºC to 85ºC)
		Altitude	up to 10,000 ft. (3 km)
	Electrical characteristics	Power consumption typical	2 W
	Electrical characteristics	Power consumption maximum	3 W
	Cabling	Cable type:: Low metal content, single-mode fiber-optic, complying with ITU-T G.652 and ISO/IEC 793-2 Type B1; Maximum distance: 10 km
		Cable length	2m to 10km with 9/125 ìm single-mode cable
		Fiber type	Single Mode
	Notes	Conditioning patch cord cables are not supported For fiber patch cords, use Ultra Physical Contact (UPC) surface termination/polish. Angled Physical Contact (APC) is not recommended
	Services	Refer to the HP website at www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

HP X131 10G X2 SC LRM Transceiver (J9144A) An X2 form-factor transceiver that supports the 10-Gigabit LRM standard, providing 10-Gigabit connectivity up to 220 m on legacy multimode fiber.	Ports	1 SC 10-GbE port (IEEE 802.3aq Type 10GBASE-LRM); Duplex: full only
	Physical characteristics	Dimensions	3.54(d) x 1.59(w) x 0.7(h) in. (9.0 x 4.05 x 1.78 cm)
		Weight	0.35 lb. (0.16 kg)
		Transceiver form factor	X2
	Environment	Operating temperature	32ºF to 158ºF (0ºC to 70ºC)
		Operating relative humidity	0% to 95%, noncondensing
		Nonoperating/Storage temperature	-40ºF to 185ºF (-40ºC to 85ºC)
		Altitude	up to 10,000 ft. (3 km)
	Electrical characteristics	Power consumption typical	3.2 W
	Electrical characteristics	Power consumption maximum	4.2 W
	Cabling	Cable type: 62.5/125 µm or 50/125 µm (core/cladding) diameter, graded-index, low metal content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2 Type A1b or A1a, respectively (a mode conditioning patch cord may be needed in some multimode fiber installations); Maximum distance: • 0.5-220m with 62.5 µm multimode cable @ 160/500 MHzkm • 0.5-220m with 62.5 µm multimode cable @ 200/500 MHzkm • 0.5-100m with 50 µm multimode cable @ 400/400 MHzkm • 0.5-220m with 50 µm multimode cable @ 500/500 MHzkm • 0.5-220m with 50 µm multimode cable @ 1500/500 MHz*km
		Cable length	.5m to 220m
		Fiber type	Multi Mode
	Notes	Wavelength: 1310nm For OM3 cable (50 ìm multimode @ 1500/500 MHz*km), a mode-conditioning patch cord is not required. Other multimode cables may require mode-conditioning patch cords to achieve the maximum distances listed above. For supported platforms and minimum software requirements to support this product, see the document titled "Support for the J9144A 10-GbE X2-SC LRM Optic" on the "HP 10-GbE Transceivers" Manuals Web page. Power Consumption: 4W Max
	Services	Refer to the HP website at http://www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

HP X112 100M SFP LC BX-D Transceiver (J9099B) A small form-factor pluggable (SFP) 100-Megabit BX (bi-directional) "downstream" transceiver that provides 100 Mbps full-duplex connectivity up to 10 km on one strand of singlemode fiber. The J9099B connects to the J9100B "upstream" transceiver, or to any IEEE-standard 100BASE-BX10-U ("upstream") device.	Ports	1 LC 100BASE-BX10 port (IEEE 802.3ah Type 100BASE-BX10-D); Duplex: full only
	Physical characteristics	Dimensions	2.7(d) x 0.55(w) x 0.48(h) in. (6.86 x 1.39 x 1.22 cm)
		Weight	0.04 lb. (0.03 kg)
	Environment	Operating temperature	32ºF to 158ºF (0ºC to 70ºC)
		Operating relative humidity	0% to 95%, noncondensing
		Nonoperating/Storage temperature	-40ºF to 185ºF (-40ºC to 85ºC)
	Cabling	Type: Single-mode fiber optic, complying with ITU-T G.652; Maximum distance: 0.5-10,000 m (single-mode fiber)
	Notes	Transmit wavelength: 1550 nm. Receive wavelength: 1310 nm. Power consumption is 1.1 watt maximum. For supported platforms and minimum software requirements to support this product, see the document titled "Support for the HP BX Transceivers" on the "HP Mini-GBICs and SFPs" Manuals Web page. The J9099B connects to the J9100B "upstream" transceiver, or to any IEEE-standard 100BASE-BX10-U ("upstream") device. (A 100-BX-D transceiver can only connect to a 100-BX-U product. You cannot connect two 100-BX-D transceivers together.)
	Services	Refer to the HP website at www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

HP X112 100M SFP LC BX-U Transceiver (J9100B) A small form-factor pluggable (SFP) 100-Megabit BX (bi-directional) "upstream" transceiver that provides 100 Mbps full-duplex connectivity up to 10 km on one strand of singlemode fiber. The J9100B connects to the J9099B "downstream" transceiver, or to any IEEE-standard 100BASE-BX10-D ("downstream") device.	Ports	1 LC 100BASE-BX10 port (IEEE 802.3ah Type 100BASE-BX10-U); Duplex: full only
	Physical characteristics	Dimensions	2.7(d) x 0.55(w) x 0.48(h) in. (6.86 x 1.39 x 1.22 cm)
		Weight	0.07 lb. (.03 kg)
	Environment	Operating temperature	32ºF to 158ºF (0ºC to 70ºC)
		Operating relative humidity	0% to 95%, noncondensing
		Nonoperating/Storage temperature	-40ºF to 185ºF (-40ºC to 85ºC)
	Cabling	Type: Single-mode fiber optic, complying with ITU-T G.652; Maximum distance: 0.5-10,000 m (single-mode fiber)
	Notes	For supported platforms and minimum software requirements to support this product, see the document titled "Support for the HP BX Transceivers" on the "HP Mini-GBICs and SFPs" Manuals Web page. The J9100B connects to the J9099B "downstream" transceiver, or to any IEEE-standard 100BASE-BX10- D ("downstream") device. (A 100-BX-U transceiver can only connect to a 100-BX-D product. You cannot connect two 100-BX-U transceivers together.) Transmit wavelength: 1310 nm. Receive wavelength: 1550 nm. Power consumption is 1.1 watts maximum.
	Services	Refer to the HP website at http://www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

HP X121 1G SFP LC LH Transceiver (J4860C) A small form-factor pluggable (SFP) Gigabit LH transceiver that provides a full-duplex Gigabit solution up to 70 km on single-mode fiber.	Ports	1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics); Duplex: full only
	Physical characteristics	Dimensions: 2.17(d) x 0.60(w) x 0.46(h) in. (5.5 x 1.53 x 1.18 cm) Weight: 0.04 lb. (0.02 kg)
	Environment	Operating temperature: -40°F to 185°F (-40°C to 85°C)
		Operating relative humidity: 0% to 95% @ 77°F (25°C), noncondensing
		Nonoperating/Storage temperature: -40°F to 185°F (-40°C to 85°C)
		Altitude: up to 10,000 ft. (3 km)
	Cabling	Cable type: Low metal content, single-mode fiber-optic, complying with ITU-T G.652 and ISO/IEC 793-2 Type B1; Maximum distance: 10-70,000 m (single-mode fiber)
	Notes	Power consumption is 0.8 watts typical with 1 watt maximum at 100% utilization. For distances less than 20 km, a 10 dB attenuator must be used. For distances between 20 km and 40 km, a 5 dB attenuator must be used. Attenuators can be purchased from most cable vendors.
	Services	Refer to the HP website at www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

HP X121 1G SFP LC SX Transceiver (J4858C) A small form-factor pluggable (SFP) Gigabit SX transceiver that provides a full-duplex Gigabit solution up to 550 m on multimode fiber.	Ports	1 LC 1000BASE-SX port; Duplex: full only
	Physical characteristics	Dimensions: 2.24(d) x 0.54(w) x 0.48(h) in. (5.69 x 1.37 x 1.22 cm) Weight: 0.04 lb. (0.02 kg) Transceiver form factor: SFP
	Environment	Operating temperature: 32°F to 158°F (0°C to 70°C)
		Operating relative humidity: 5% to 85%, noncondensing
		Nonoperating/Storage temperature: -40°F to 203°F (-40°C to 85°C)
		Altitude: up to 10,000 ft. (3 km)
	Electrical characteristics	Power consumption typical: 0.4 W
	Electrical characteristics	Power consumption maximum: 0.7 W
	Cabling	Type: 62.5/125 µm or 50/125 µm (core/cladding) diameter, graded-index, low metal content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2 Type A1b or A1a, respectively; Maximum distance: 2-220 m (62.5 µm core diameter, 160 MHzkm bandwidth 2-275 m (62.5 µm core diameter, 200 MHzkm bandwidth 2-500 m (50 µm core diameter, 400 MHzkm bandwidth) 2-550 m (50 µm core diameter, 500 MHzkm bandwidth)
		Cable length: 2-550m
		Fiber type: Multi Mode
	Services	Refer to the HP website at http://www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

HP X121 1G SFP LC LX Transceiver (J4859C) HP X121 1G SFP LC LX Transceiver: An SFP format gigabit transceiver with LC connectors using LX technology.	Ports	1 LC 1000BASE-LX port (IEEE 802.3z Type 1000BASE-LX); Duplex: full only
	Physical characteristics	Dimensions: 2.24(d) x 0.54(w) x 0.486(h) in. (5.69 x 1.37 x 1.23 cm) Weight:0.04 lb. (0.02 kg)
	Environment	Operating temperature: 32°F to 158°F (0°C to 70°C)
		Operating relative humidity: 0% to 85%, noncondensing
		Nonoperating/Storage temperature: -40°F to 212°F (-40°C to 100°C)
		Altitude: up to 10,000 ft. (3 km)
	Cabling	Type: Either single mode or multimode; 62.5/125 µm or 50/125 µm (core/cladding) diameter, graded-index, low metal content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2 Type A1b or A1a, respectively; Low metal content, single-mode fiber-optic, complying with ITU-T G.652 and ISO/IEC 793-2 Type B1; Maximum distance: 2-550 m (multimode 62.5 µm core diameter, 500 MHzkm bandwidth) 2-550 m (multimode 50 µm core diameter, 400 MHzkm bandwidth) 2-550 m (multimode 50 µm core diameter, 500 MHz*km bandwidth) 2-10,000 m (single-mode fiber)
	Notes	A mode conditioning patch cord may be needed in some multimode fiber installations. Wavelength: 1310nm Power Consumption: < 500mW Typical
	Services	Refer to the HP website at www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

HP X122 1G SFP LC BX-D Transceiver (J9142B) A small form-factor pluggable (SFP) Gigabit-BX (bi-directional) "downstream" transceiver that provides a full-duplex Gigabit solution up to 10 km on one strand of single-mode fiber. The J9142B connects to the J9143B "upstream" transceiver, or to any IEEE-standard 1000BASE-BX10-U ("upstream") device.	Ports	1 LC 1000BASE-BX10 port (IEEE 802.3ah Type 1000BASE-BX10-D); Duplex: full only
	Physical characteristics	Dimensions	2.19(d) x 0.54(w) x 0.46(h) in. (5.57 x 1.37 x 1.18 cm)
		Weight	0.04 lb. (0.02 kg)
	Environment	Operating temperature	32ºF to 158ºF (0ºC to 70ºC)
		Operating relative humidity	0% to 95%, non-condensing
		Non-operating/ Storage temperature	–40ºF to 185ºF –40ºC to 85ºC)
	Cabling	Type: Single-mode fiber optic, complying with ITU-T G.652; Maximum distance: 0.5-10,000 m (single-mode fiber)
	Notes	Transmit wavelength: 1490 nm. Receive wavelength: 1310 nm. Power consumption is 1 watt maximum. For supported platforms and minimum software requirements to support this product, see the document titled "Support for the HP BX Transceivers" on the "HP Mini-GBICs and SFPs" Manuals Web page. The J9142B connects to the J9143B "upstream" transceiver, or to any IEEE-standard 1000BASE-BX10-U ("upstream") device. (A 1000-BX-D transceiver can only connect to a 1000-BX-U product. You cannot connect two 1000-BX-D transceivers together.)
	Services	Refer to the HP website at: http://www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

HP X122 1G SFP LC BX-U Transceiver (J9143B) A small form-factor pluggable (SFP) Gigabit-BX (bi-directional) "upstream" transceiver that provides a full-duplex Gigabit solution up to 10 km on one strand of single-mode fiber. The J9143B connects to the J9142B "downstream" transceiver, or to any IEEE-standard 1000BASE-BX10-D ("downstream") device.	Ports	1 LC 1000BASE-BX10 port (IEEE 802.3ah Type 1000BASE-BX10-U); Duplex: full only
	Physical characteristics	Dimensions	2.19(d) x 0.54(w) x 0.46(h) in. (5.57 x 1.37 x 1.18 cm)
		Weight	0.04 lb. (0.02 kg)
	Environment	Operating temperature	32ºF to 158ºF (0ºC to 70ºC)
		Operating relative humidity	0% to 95%, non-condensing
		Non-operating/ Storage temperature	–40ºF to 185ºF –40ºC to 85ºC)
	Cabling	Type: Single-mode fiber optic, complying with ITU-T G.652; Maximum distance: 0.5-10,000 m (single-mode fiber)
	Notes	Transmit wavelength: 1310 nm. Receive wavelength: 1490 nm. For supported platforms and minimum software requirements to support this product, see the document titled "Support for the HP BX Transceivers" on the "HP Mini-GBICs and SFPs" Manuals Web page. The J9143B connects to the J9142B "downstream" transceiver, or to any IEEE-standard 1000BASE-BX10-D ("downstream") device. (A 1000-BX-U transceiver can only connect to a 1000-BX-D product. You cannot connect two 1000-BX-U transceivers together.) Power consumption is 1 watt maximum.
	Services	Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

HP 0.5 m Multimode OM3 LC/LC Optical Cable (AJ833A)	Cabling	Cable type: 50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of up to 300 m Maximum distance: 10Gbps Transfer Rate (Ethernet): 300m
	Notes	Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um fiber optic cable and Ethernet assembly with LC duplex connectors on one end and LC duplex connectors on other end. Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um Coating diameter: 245 ± 10um Optical glass: Bandwidth: For LED sources: 1500/500 MHz-km @850/1300nm. Optical glass: Bandwidth: For Laser sources: 2000/500 MHz-km @850/1300nm. VCSEL Laser sources: 600 / 600 meters @850/1300nm for Gigabit Ethernet compliant links. CABLE: The cable is duplex zipcord graded index 50/125um multimode optical fiber and designed to work in both the 850 and 1300 nm wavelength windows. BULK CABLE & CABLE ASSEMBLY CONFIGURATION: Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic. Jacket Color: Aqua for OM3 multimode per TIA 598 Boot Color: White Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M added for lengths > 30 meters. Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310 nm @ 23°C as tested in accordance with EIA 455-46. Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
	Services	Refer to the HP website at http://www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

HP Premier Flex LC/LC Multi-mode OM4 2 fiber 1m Cable (QK732A)

Notes