HPE Aruba 2915 Switch Series: характеристики и документация

Aruba 2915 Switch Series

Models
Aruba 2915 8G PoE Switch	J9562A

Key features

Scalable 10/100/1000 connectivity
L2 and L3 switching capabilities
sFlow, ACLs, and rate limiting
Energy-efficient design and quiet operation
Rack-mountable, compact form factor

Product overview

The Aruba 2915 Switch Series is a fully managed, eight-port, 10/100/1000 switch with two additional dual-personality gigabit Ethernet ports for copper or SFP connectivity. Bringing together static and RIP IPv4 routing, robust security and management, enterprise class features. Limited Lifetime Warranty, software updates included. These PoE switch delivers a comprehensive and cost-effective solution.

The 2915 Switch Series has a fan-less design for quiet operation, making it suitable for deployments in open spaces. In addition, its compact form factor allows for flexible deployments—including wall, surface, or rack mounting. These switches can be deployed at the enterprise edge and remote branch offices, as well as on converged networks.

Features and benefits

Quality of Service (QoS)

Selectable queue configuration
performance and/or traffic reliability can be increased by selecting the number of queues that best meet the requirements of network applications; the switch will map eight priorities to either two or four queues
Class of Service (CoS)
sets the IEEE 802.1p priority tag based on IP address, IP Type of Service (ToS), Layer 3 protocol, TCP/UDP port number, source port, and DiffServ
Layer 4 prioritization
enables prioritization based on TCP/UDP port numbers
Traffic prioritization (IEEE 802.1p)
allows real-time traffic classification into eight priority levels mapped to four queues
Rate limiting
per-port ingress-enforced maximums
Flow control
helps ensure reliable communications during full-duplex operation
Type of service:

- IP precedence
honors IP precedence bits and allows mapping to a priority queue

- Differentiated Services Code Point values
honors Differentiated Services Code Point (DSCP) bits and allows mapping to a priority queue

Management

Choice of management interfaces

- Web GUI
easy-to-use graphical interface allows configuration of the switch from any Web browser

- Command-line interface (CLI)
robust CLI provides advanced configuration and diagnostics

- Simple Network Management Protocol (SNMPv2c/SNMPv3)
allows switch to be managed with a variety of third-party network management applications

Multiple configuration files
configuration file management tools allow up to three configuration files to be managed and stored on the switch
Dual flash images
provide independent primary and secondary operating system files for backup while upgrading
Command authorization
leverages RADIUS to link a custom list of CLI commands to an individual network administrator's login; also provides an audit trail
Front-panel LEDs

- Locator LED
allows users to set the locator LED on a specific switch to either turn on, blink, or turn off; simplifies troubleshooting by making it easy to locate a particular switch within a rack of similar switches

- Per-port LEDs
provides an at-a-glance view of status, activity, speed, and full-duplex operation

- Power and fault LED
display any issues

Integration with HPE PCM
enables discovery, mapping, logging, and configuration via PCM, which is available as a free download from the Web
Network management
HPE Intelligent Management Center (IMC) centrally configures, updates, monitors, and troubleshoots
Comware CLI

- Comware-compatible CLI
bridges the experience of Hewlett Packard Enterprise Comware CLI users who are using the ProVision CLI

- Display and fundamental Comware CLI commands
are natively embedded in the switch CLI; display output is formatted as on Comware-based switches; fundamental commands provide Comware-familiar initial switch setup

- Configuration Comware CLI commands
when Comware commands are entered, CLI help is elicited to formulate the correct ProVision software CLI command

Connectivity

Dual-personality functionality
two 10/100/1000 ports or SFP slots provide optional fiber connectivity such as Gigabit-SX, -LX, -LH, 100-FX, 100-BX, and 1000-BX
IEEE 802.3af Power over Ethernet
provides up to 15.4 W per port to IEEE 802.3af-compliant PoE-powered devices such as IP phones, wireless access points, and security cameras (see product specifications for total PoE power available)
Auto-MDIX|
automatically adjusts for straight-through or crossover cables on all 10/100/1000 ports
RJ-45 serial console port
provides easy accessibility on the front of unit to the switch CLI
IPv6:

- IPv6 host
the switches can be managed and deployed at the edge of IPv6 networks

- Dual stack (IPv4/IPv6)
provides transition mechanism from IPv4 to IPv6; supports connectivity for both protocols

Single IP address management
provides single IP address management for a virtual stack of up to 16 switches

Resiliency and high availability

IEEE 802.1s Multiple Spanning Tree
provides high link availability in multiple VLAN environments by allowing multiple spanning trees; provides legacy support for IEEE 802.1d and IEEE 802.1w
Port trunking and link aggregation

- Trunking
supports up to eight links per trunk to increase bandwidth and create redundant connections

- IEEE 802.3ad Link Aggregation Protocol (LACP)
eases configuration of trunks through automatic configuration

SmartLink
provides easy-to-configure link redundancy of active and standby links

Layer 2 switching

GARP VLAN Registration Protocol
allows automatic learning and dynamic assignment of VLANs
VLAN support and tagging
supports IEEE 802.1Q (4,094 VLAN IDs) and 256 VLANs simultaneously
Per-VLAN Spanning Tree Plus (PVST+)
allows each VLAN to build a separate spanning tree to improve link bandwidth usage in network environments with multiple VLANs

Layer 3 routing

Static IP routing
provides manually configured routing; includes ECMP capability
Routing Information Protocol (RIP)
provides RIPv1 and RIPv2 routing

Security

Access control lists (ACLs)
provide IP Layer 3 filtering based on source/destination IP address/subnet and source/destination TCP/UDP port number
Identity-driven ACL
enables implementation of a highly granular and flexible access security policy and VLAN assignment specific to each authenticated network user
Source-port filtering
allows only specified ports to communicate with each other
RADIUS/TACACS+
eases switch management security administration by using a password authentication server
Secure protocols for encryption of management traffic

- Secure Shell (SSHv2)
encrypts all transmitted data for secure remote CLI access over IP networks

- Secure Sockets Layer (SSL)
encrypts all HTTP traffic, allowing secure access to the browser-based management GUI in the switch

- Secure FTP (SFTP)
encrypts uploads and downloads of configuration files

Port security
allows access only to specified MAC addresses, which can be learned or specified by the administrator
Dynamic IP lockdown
works with DHCP protection to block traffic from unauthorized hosts, preventing IP source address spoofing
DHCP protection
blocks DHCP packets from unauthorized DHCP servers, preventing denial-of-service attacks
Dynamic ARP protection
blocks ARP broadcasts from unauthorized hosts, preventing eavesdropping or theft of network data
MAC address lockout
prevents configured particular MAC addresses from connecting to the network
MAC address lockdown
allows only specified MAC addresses access to the network on a specified port
Multiple user authentication methods

- IEEE 802.1X
is an industry-standard method of user authentication using an IEEE 802.1X supplicant on the client in conjunction with a RADIUS server

- Web-based authentication
similar to IEEE 802.1X, it provides a browser-based environment to authenticate clients that do not support the IEEE 802.1X supplicant

- MAC-based authentication
client is authenticated with the RADIUS server based on the client's MAC address

Authentication flexibility—2 IEEE 802.1X
provides authentication of multiple IEEE 802.1X users per port; prevents user "piggybacking" on another user's IEEE 802.1X authentication
Protected ports
prevents designated ports from communicating with each other while allowing access to unprotected ports
Per-port broadcast throttling
selectively configures broadcast control on heavy traffic port uplinks
Physical security

- Front-panel buttons
provides the ability to disable reset and clear buttons on the front panel for added security

- Kensington Lock slot
includes a Kensington Lock slot for securing the switches in open-space deployments

Spanning Tree Protocol Root Guard
when running the Spanning Tree Protocol, it protects the root bridge from malicious attacks or configuration mistakes
STP BPDU port protection
blocks Bridge Protocol Data Units (BPDUs) on ports that do not require BPDUs, preventing forged BPDU attacks

Convergence

IP multicast snooping and data-driven IGMP
automatically prevent flooding of IP multicast traffic
LLDP-MED (Media Endpoint Discovery)
defines a standard extension of LLDP that stores values for parameters such as QoS and VLAN to configure automatically network devices such as IP phones
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
is an automated device discovery protocol that provides easy mapping of network management applications
PoE allocations
support multiple methods (automatic, IEEE 802.3af class, LLDP-MED, or user specified) to allocate PoE power for more efficient energy savings
Local MAC Authentication
assigns attributes such as VLAN and QoS using locally configured profile that can be a list of MAC prefixes

Unified Wired and Wireless

HTTP redirect function
supports HPE Intelligent Management Center (IMC) bring your own device (BYOD) solution

Monitor and diagnostics

Port mirroring
enables traffic on a port to be simultaneously sent to a network analyzer for monitoring
Network tools
CLI includes telnet client, ping, traceroute, and Layer 2 link test tools for diagnostics
Logging
local and remote logging of events via SNMP (v2c and v3) and syslog
Troubleshooting
ingress and egress port monitoring enable network problem solving
Uni-Directional Link Detection (UDLD)
monitors a link between two switches and blocks the ports on both ends of the link if the link goes down at any point between the two devices
Find-Fix-Inform
finds and fixes common network problems automatically, then informs the administrator
RMON, XRMON, sFlow, and SMON
provide advanced monitoring and reporting capabilities for statistics, history, alarms, and events
Port monitoring for network threats
provides sampled port traffic, using sFlow technology, to the HPE Network Immunity Manager application for network-behavior-anomaly-detection (NBAD) analysis—to detect and mitigate threats at the port where they originated

Flexibility

Flexible mounting

- Rackable
can be mounted in a standard 19-inch rack with included hardware

- Wall mountable
can be mounted to a wall using included hardware

- Surface mountable
can be mounted above or below a surface (such as a desk or table) using included hardware

Compact siz
product is designed to reduce space requirements (see product specifications for exact dimensions)
NEW Power supply clip
provides the ability to attach or detach the power supply from the device, allowing for either an integrated solution or a separate one, depending on deployment requirements

Product Architecture

Energy-efficient design

- Fans
fanless design helps reduce power consumption

- Port LEDs
port link and activity LEDs can be turned off to conserve energy

- Port low-power mode option
when no link is detected on a port, the port will automatically go into low-power mode to conserve energy

Warranty and support

Limited Lifetime Warranty
See http://www.hpe.com/networking/warrantysummary for warranty and support information included with your product purchase.
Software releases
to find software for your product, refer to http://www.hpe.com/networking/support ; for details on the software releases available with your product purchase, refer to http://www.hpe.com/networking/warrantysummary

Build To Order: BTO is a standalone unit with no integration. BTO products ship standalone are not part of a CTO or Rack-Shippable solution.

Aruba 2915 8G PoE Switch		J9562A
8 RJ-45 autosensing 10/100/1000 PoE ports 2 dual-personality ports min=0 \ max=2 SFP Transceivers 1U - Height		See Configuration NOTE:1, 2

No Power Cord		J9562A#AC3
No Localized Power Cord Selected

Configuration Rules:

Note 1	The following Transceivers install into this switch:
	HPE X111 100M SFP LC FX Transceiver	J9054C
	HPE X121 1G SFP LC LH Transceiver	J4860C
	HPE X121 1G SFP LC LX Transceiver	J4859C
	HPE X121 1G SFP LC SX Transceiver	J4858C

Note 2	Localization required. (See Localization Menu for list.)

Internal Power Supplies

No Power supplies

Transceivers

SFP Transceivers

HPE X121 1G SFP LC SX Transceiver		J4858C
HPE X121 1G SFP LC LX Transceiver		J4859C
HPE X111 100M SFP LC FX Transceiver		J9054C
HPE X121 1G SFP LC LH Transceiver		J4860C

Cables

Multi-Mode Cables

HPE LC to LC Multi-mode OM3 2-Fiber 0.5m 1-Pack Fiber Optic Cable		AJ833A

Switch Enclosure Options

Mounting Kit

Aruba X510 1U Cable Guard		J9700A

Aruba 2915 8G PoE Switch (J9562A)
Included accessories	1 HP X520 1U Power Adapter Shelf (J9701A)
I/O ports and slots	8 RJ-45 autosensing 10/100/1000 PoE ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3af PoE) Media Type: Auto-MDIX Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
I/O ports and slots	2 dual-personality ports; each port can be used as either an RJ-45 10/100/1000 port (IEEE 802.3 Type 10BASE-T; an IEEE 802.3u Type 100BASE-TX; an IEEE 802.3ab 1000BASE-T Gigabit Ethernet); or an SFP slot (for use with SFP transceivers)
Additional ports and slots	1 RJ-45 serial console port
Physical characteristics	Dimensions	10(w) x 6.28(d) x 1.75(h) in (25.4 x 15.95 x 4.45 cm) (1U height)
Physical characteristics	Weight	3.66 lb (1.66 kg) including power adapter and power cord
Memory and processor	Processor	Freescale PowerPC 8313 @ 333 MHz, 32 MB flash, 128 MB DDR2 SDRAM; packet buffer size: 512 KB dynamically all
Mounting and enclosure	Mounts in an EIA-standard 19 in. telco rack or equipment cabinet; horizontal surface mounting, wall mounting
Performance	100 Mb Latency	< 5.3 µs (LIFO 64-byte packets)
	1000 Mb Latency	< 2.7 µs (LIFO 64-byte packets)
	Throughput	up to 14.8 Mpps
	Switching capacity	20 Gbps
	MAC address table size	8000 entries
Environment	Operating temperature	32°F to 113°F (0°C to 45°C)
	Operating relative humidity	15% to 95% @ 104°F (40°C), noncondensing
	Nonoperating/Storage temperature	-40°F to 158°F (-40°C to 70°C)
	Nonoperating/Storage relative humidity	15% to 95% @ 149°F (65°C), noncondensing
	Altitude	up to 10,000 ft (3 km)
	Acoustic	Power: 0 dB, Pressure: 0 dB
Electrical characteristics	Description	Use only the external power adapter module (5070-6082, PA1 AC adapter) supplied with this product.
	Maximum heat dissipation	89 BTU/hr (93.9 kJ/hr)
	Voltage	100 - 240 VAC, rated (depending on power supply chosen)
	Current	1.5 A
	Maximum power rating	86 W
	Idle power	11 W
	PoE power	67 W PoE
	Frequency	50/60 Hz
	Notes	Idle power is the actual power consumption of the device with no ports connected. Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated. PoE power is the total power budget available to all PoE ports.
Safety	cUL (CSA 22.2 No. 60950); CE Labeled; UL 60950-1; UL Listed; CAN/CSA 22.2 No. 60950; EN 60825; AS/NZS 60950; IEC 60950-1; EN 60950-1
Emissions	FCC part 15 Class A; VCCI Class A; EN 55022 Class A; CISPR 22 Class A; ICES-003 (Canada); AS/NZS CISPR 22; IEC/EN 61000-3-2; IEC/EN 61000-3-3; IEC 61000:4-2, 4-3, 4-4, 4-5, 4-6, 4-8, 4-11
Immunity	Generic	EN 55024, CISPR 24
	EN	EN 55024, CISPR 24
	ESD	IEC 61000-4-2
	Radiated	IEC 61000-4-3
	EFT/Burst	IEC 61000-4-4
	Surge	IEC 61000-4-5
	Conducted	IEC 61000-4-6
	Power frequency magnetic field	IEC 61000-4-8
	Voltage dips and interruptions	IEC 61000-4-11
	Harmonics	EN 61000-3-2, IEC 61000-3-2
	Flicker	EN 61000-3-3, IEC 61000-3-3
Management	IMC - Intelligent Management Center; command-line interface; Web browser; configuration menu; out-of-band management (serial RS-232C); IEEE 802.3 Ethernet MIB; Repeater MIB; Ethernet Interface MIB
Notes	When using mini-GBICs with this product, mini-GBICs with revision "B" or later (product number ends with the letter "B" or later, e.g., J4858B, J4859C) are required. This product comes with a power supply clip adapter. The adapter dimensions are 1.7(d) x 10.7(w) x 3.8(h) in. (4.35 x 27.25 x 9.6 cm). The weight of the power supply clip adapter is .31 lb (.14 kg).
Services	Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office

Standards and protocols

Denial of service protection
Automatic Filtering of well known Denial of Service
Packets

Device management
RFC 1591 DNS (client)
Multiple Configuration Files
Multiple Software Images
SSHv1/SSHv2 Secure Shell
TACACS/TACACS+
Web UI

General protocols
IEEE 802.1D MAC Bridges
IEEE 802.1p Priority
IEEE 802.1Q VLANs
IEEE 802.1s Multiple Spanning Trees
IEEE 802.1w Rapid Reconfiguration of Spanning Tree
IEEE 802.3 Type 10BASE-T
IEEE 802.3ab 1000BASE-T
IEEE 802.3ad Link Aggregation Control Protocol (LACP)
IEEE 802.3af Power over Ethernet
IEEE 802.3u 100BASE-X
IEEE 802.3x Flow Control
RFC 768 UDP
RFC 783 TFTP Protocol (revision 2)
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 TELNET
RFC 868 Time Protocol
RFC 951 BOOTP
RFC 1058 RIPv1
RFC 1350 TFTP Protocol (revision 2)
RFC 1723 RIP v2
RFC 1812 IPv4 Routing
RFC 1918 Address Allocation for Private Internet
RFC 2030 Simple Network Time Protocol (SNTP) v4
RFC 2131 DHCP
RFC 2453 RIPv2
UDLD (Uni-directional Link Detection)

IP multicast
RFC 3376 IGMPv3 (host joins only)

IPv6
RFC 1981 IPv6 Path MTU Discovery
RFC 2460 IPv6 Specification
RFC 2464 Transmission of IPv6 over Ethernet Networks
RFC 2925 Remote Operations MIB (Ping only)
RFC 3315 DHCPv6 (client only)
RFC 3484 Default Address Selection for IPv6
RFC 3513 IPv6 Addressing Architecture
RFC 3596 DNS Extension for IPv6
RFC 3810 Multicast Listener Discovery Version 2 (MLDv2) for IPv6
RFC 4022 MIB for TCP

RFC 4113 MIB for UDP
RFC 4251 SSHv6 Architecture
RFC 4252 SSHv6 Authentication
RFC 4253 SSHv6 Transport Layer
RFC 4291 IP Version 6 Addressing Architecture
RFC 4293 MIB for IP
RFC 4419 Key Exchange for SSH
RFC 4443 ICMPv6
RFC 4861 IPv6 Neighbor Discovery
RFC 4862 IPv6 Stateless Address Auto-configuration

MIBs
RFC 1155 Structure & ID of Mgmt Info for TCP/IP Internets
RFC 1213 MIB II
RFC 1493 Bridge MIB
RFC 2021 RMONv2 MIB
RFC 2578 Structure of Management Information Version 2 (SMIv2)
RFC 2613 SMON MIB
RFC 2618 RADIUS Client MIB
RFC 2620 RADIUS Accounting MIB
RFC 2665 Ethernet-Like-MIB
RFC 2668 802.3 MAU MIB
RFC 2674 802.1p and IEEE 802.1Q Bridge MIB
RFC 2737 Entity MIB (Version 2)
RFC 2863 The Interfaces Group MIB
RFC 4836 Managed Objects for 802.3 Medium Attachment Units (MAU)

Network management
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
RFC 1098 A Simple Network Management Protocol (SNMP)
RFC 2819 Four groups of RMON: 1 (statistics), 2 (history), 3 (alarm) and 9 (events)
RFC 3176 sFlow
RFC 5424 Syslog Protocol
SNMPv1/v2c/v3

QoS/CoS
RFC 2474 DiffServ precedence, with 4 queues per
port
RFC 2475 DiffServ Architecture
RFC 2597 DiffServ Assured Forwarding (AF)
RFC 2598 DiffServ Expedited Forwarding (EF)
Ingress Rate Limiting

Security
IEEE 802.1X Port Based Network Access Control
RFC 1492 TACACS+
RFC 2138 RADIUS Authentication
RFC 2866 RADIUS Accounting
Access Control Lists (ACLs)
MAC Authentication
MAC Lockdown
MAC Lockout
Port Security
Secure Sockets Layer (SSL)
Web Authentication

Aruba 2915 Switch Series accessories

Aruba 2915 8G PoE Switch (J9562A)
HPE X121 1G SFP LC SX Transceiver	J4858C
HPE X121 1G SFP LC LX Transceiver	J4859C
HPE X121 1G SFP LC LH Transceiver	J4860C
HPE X111 100M SFP LC FX Transceiver	J9054C
HPE LC to LC Multi-mode OM3 2-Fiber 0.5m 1-Pack Fiber Optic Cable	AJ833A
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 1m Cable	QK732A
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 2m Cable	QK733A
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 5m Cable	QK734A
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 15m Cable	QK735A
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 30m Cable	QK736A
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 50m Cable	QK737A
Aruba X510 1U Cable Guard	J9700A

NOTE: Details are not available for all accessories. The following specifications were available at the time of publication.

HPE X121 1G SFP LC SX Transceiver (J4858C) A small form-factor pluggable (SFP) Gigabit SX transceiver that provides a full-duplex Gigabit solution up to 550 m on multimode fiber.	Ports	1 LC 1000BASE-SX port; Duplex: full only
	Physical characteristics	Dimensions: 2.24(d) x 0.54(w) x 0.48(h) in. (5.69 x 1.37 x 1.22 cm) Weight: 0.04 lb. (0.02 kg) Transceiver form factor: SFP
	Environment	Operating temperature: 32°F to 158°F (0°C to 70°C)
		Operating relative humidity: 5% to 85%, noncondensing
		Nonoperating/Storage temperature: -40°F to 203°F (-40°C to 85°C)
		Altitude: up to 10,000 ft. (3 km)
	Electrical characteristics	Power consumption typical: 0.4 W
	Electrical characteristics	Power consumption maximum: 0.7 W
	Cabling	Type: 62.5/125 µm or 50/125 µm (core/cladding) diameter, graded-index, low metal content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2 Type A1b or A1a, respectively; Maximum distance: 2-220 m (62.5 µm core diameter, 160 MHzkm bandwidth 2-275 m (62.5 µm core diameter, 200 MHzkm bandwidth 2-500 m (50 µm core diameter, 400 MHzkm bandwidth) 2-550 m (50 µm core diameter, 500 MHzkm bandwidth)
		Cable length: 2-550m
		Fiber type: Multi Mode
	Services	Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office

HPE X121 1G SFP LC LX Transceiver (J4859C) HPE X121 1G SFP LC LX Transceiver: An SFP format gigabit transceiver with LC connectors using LX technology.	Ports	1 LC 1000BASE-LX port (IEEE 802.3z Type 1000BASE-LX); Duplex: full only
	Physical characteristics	Dimensions: 2.24(d) x 0.54(w) x 0.486(h) in. (5.69 x 1.37 x 1.23 cm) Weight:0.04 lb. (0.02 kg)
	Environment	Operating temperature: 32°F to 158°F (0°C to 70°C)
		Operating relative humidity: 0% to 85%, noncondensing
		Nonoperating/Storage temperature: -40°F to 212°F (-40°C to 100°C)
		Altitude: up to 10,000 ft. (3 km)
	Cabling	Type: Either single mode or multimode; 62.5/125 µm or 50/125 µm (core/cladding) diameter, graded-index, low metal content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2 Type A1b or A1a, respectively; Low metal content, single-mode fiber-optic, complying with ITU-T G.652 and ISO/IEC 793-2 Type B1; Maximum distance: 2-550 m (multimode 62.5 µm core diameter, 500 MHzkm bandwidth) 2-550 m (multimode 50 µm core diameter, 400 MHzkm bandwidth) 2-550 m (multimode 50 µm core diameter, 500 MHz*km bandwidth) 2-10,000 m (single-mode fiber)
	Notes	A mode conditioning patch cord may be needed in some multimode fiber installations. Wavelength: 1310nm Power Consumption: < 500mW Typical
	Services	Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office

HPE X121 1G SFP LC LH Transceiver (J4860C) A small form-factor pluggable (SFP) Gigabit LH transceiver that provides a full-duplex Gigabit solution up to 70 km on single-mode fiber.	Ports	1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics); Duplex: full only
	Physical characteristics	Dimensions: 2.17(d) x 0.60(w) x 0.46(h) in. (5.5 x 1.53 x 1.18 cm) Weight: 0.04 lb. (0.02 kg)
	Environment	Operating temperature: -40°F to 185°F (-40°C to 85°C)
		Operating relative humidity: 0% to 95% @ 77°F (25°C), noncondensing
		Nonoperating/Storage temperature: -40°F to 185°F (-40°C to 85°C)
		Altitude: up to 10,000 ft. (3 km)
	Cabling	Cable type: Low metal content, single-mode fiber-optic, complying with ITU-T G.652 and ISO/IEC 793-2 Type B1; Maximum distance: 10-70,000 m (single-mode fiber)
	Notes	Power consumption is 0.8 watts typical with 1 watt maximum at 100% utilization. For distances less than 20 km, a 10 dB attenuator must be used. For distances between 20 km and 40 km, a 5 dB attenuator must be used. Attenuators can be purchased from most cable vendors.
	Services	Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office

HPE X111 100M SFP LC FX Transceiver (J9054C) HPE X111 100M SFP LC FX Transceiver: An SFP format 100-megabit transceiver with LC connectors using FX technology.	Ports		1 LC 100BASE-FX port (IEEE 802.3u Type 100BASE-FX); Duplex: half or full
	Physical characteristics		Dimensions: 2.7(d) x 0.54(w) x 0.48(h) in. (6.86 x 1.38 x 1.22 cm) Weight: 0.06 lb. (0.03 kg)
	Environment		Operating temperature: 32°F to 158°F (0°C to 70°C)
			Operating relative humidity: 5% to 95%
			Nonoperating/Storage temperature: -40°F to 185°F (-40°C to 85°C)
			Nonoperating/Storage relative humidity: 5% to 85%
			Altitude: up to 10,000 ft. (3 km)
	Cabling		Cable type: 62.5/125 ìm or 50/125 ìm (core/cladding) diameter, graded-index, low metal content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2 Type A1b or A1a, respectively; Maximum distance: 2 km (full duplex) or 412 m (half duplex)

	Notes		Transmitter wavelength: 1310nm Power consumption is 1.1 watt maximum. For supported platforms and minimum software requirements to support this product, see the document titled "Support for the J9054C 100-FX SFP-LC Transceiver" on the "ProCurve Mini-GBICs and SFPs" Manuals Web page.
	Services		Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office

HPE LC to LC Multi-mode OM3 2-Fiber 0.5m 1-Pack Fiber Optic Cable (AJ833A)		Cabling	Cable type: 50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of up to 300 m Maximum distance: 10Gbps Transfer Rate (Ethernet): 300m
		Notes	Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um fiber optic cable and Ethernet assembly with LC duplex connectors on one end and LC duplex connectors on other end. Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um Coating diameter: 245 ± 10um Optical glass: Bandwidth: For LED sources: 1500/500 MHz-km @850/1300nm. Optical glass: Bandwidth: For Laser sources: 2000/500 MHz-km @850/1300nm. VCSEL Laser sources: 600 / 600 meters @850/1300nm for Gigabit Ethernet compliant links. CABLE: The cable is duplex zipcord graded index 50/125um multimode optical fiber and designed to work in both the 850 and 1300 nm wavelength windows. BULK CABLE & CABLE ASSEMBLY CONFIGURATION: Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic. Jacket Color: Aqua for OM3 multimode per TIA 598 Boot Color: White Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M added for lengths > 30 meters. Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310 nm @ 23°C as tested in accordance with EIA 455-46. Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
		Services	Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office

HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 1m Cable (QK732A)

Notes

Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um duplex cable and Ethernet assembly with LC duplex connectors on each end.

Core Diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating diameter: 245 ± 10um
Bandwidth: 3000 MHz-km @ 850nm (Laser)
Jacket Color: Blue
Jacket Material: Riser Grade - Low Smoke Zero Halogen (LSZH) thermoplastic
Boot Color: White
Outer Jacket Print: HPE PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white stripe that runs the entire length of the cable.
Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added for lengths >30m
Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @ 23°C as tested in accordance with EIA 455-45

Services