Dell PowerEdge T130: руководство по обслуживанию

Processor

Specification

Type

The PowerEdge T130 supports any one of the processors listed here:

• Intel E3-1200 v5 or v6 series
• Intel Core i3 6100 series
• Intel Celeron G3900 series
• Intel Celeron G3930
• Intel Pentium G4500 series
• Intel Pentium G4600 series

PCI Express expansion slots

Specification

Slot 1

One full-height, half-length x4 PCIe Gen3 card slot connected to processor

Slot 2

One full-height, half-length x8 PCIe Gen3 card slot connected to processor

Slot 3

One full-height, full-length x1 PCIe Gen3 card slot connected to Platform Controller Hub (PCH)

Slot 4

One full-height, full-length x4 PCIe Gen3 card slot connected to PCH

Memory

Specification

Architecture

1600 MT/s, 1866 MT/s, 2133 MT/s, or 2400 MT/s DDR4 Unbuffered DIMMs

Support for advanced ECC or memory optimized operation

Memory module sockets

Four 288-pin sockets

Memory module capacities (UDIMM)

4 GB (single-rank), 8 GB (single- and dual-rank), 16 GB (single- and dual-rank)

Minimum RAM

4 GB

Maximum RAM

64 GB

Power supply unit

Specification

Power rating per power supply unit

290 W (Bronze) AC (100–240 V, 50/60 Hz, 5.4 A)

Heat dissipation

989 BTU/hr maximum (290 W power supply)

NOTE Heat dissipation is calculated by using the power supply wattage rating.

Voltage

100–240 V AC, autoranging, 50/60 Hz

NOTE This system is also designed to be connected to IT power systems with a phase-to-phase voltage not exceeding 230 V.

Storage controller

Specification

Storage controller type

PERC H730, PERC H330, PERC H830, PERC S130.

NOTE Your system supports software RAID S130 and a PERC card.

For more information on software RAID, see the Dell PowerEdge RAID Controller (PERC) documentation at Dell.com/storagecontrollermanuals.

NOTE The upgrade from embedded controller or Software RAID controller to Hardware RAID controller is not supported.

The PowerEdge T130 system supports SAS, SATA, and Nearline SAS hard drives.

Drives

Specification

Four hard drive system

Up to four 3.5-inch, internal, cabled SATA and nearline SAS hard drives.

NOTE NOTE: The PowerEdge T130 does not support hard drives higher than 5 TB.

The PowerEdge T130 system supports Integrated Matrox G200 with iDRAC8 and 16 MB application memory.

Temperature

Specifications

Storage

–40°C to 65°C (–40°F to 149°F)

Continuous operation (for altitude less than 950 m or 3117 ft)

10°C to 35°C (50°F to 95°F) with no direct sunlight on the equipment.

Maximum temperature gradient (operating and storage)

20°C/h (68°F/h)

Relative humidity

Specifications

Storage

5% to 95% RH with 33°C (91°F) maximum dew point. Atmosphere must be non-condensing at all times.

Operating

10% to 80% Relative Humidity with 29°C (84.2°F) maximum dew point.

Maximum vibration

Specifications

Operating

0.26 G_rms at 5 Hz to 350 Hz (operation orientation).

Storage

1.88 G_rms at 10 Hz to 500 Hz for 15 min (all six sides tested).

Maximum shock

Specifications

Operating

Six consecutively executed shock pulses in the positive and negative x, y, and z axes of 31G for up to 2.6 ms.

Storage

Six consecutively executed shock pulses in the positive and negative x, y, and z axes (one pulse on each side of the system) of 71 G for up to 2 ms.

Maximum altitude

Specifications

Operating

30482000 m (10,0006560 ft).

Storage

12,000 m (39,370 ft).

Operating temperature de-rating

Specifications

Up to 35 °C (95 °F)

Maximum temperature is reduced by 1°C/300 m (33.8°F/984.25 ft) above 950 m (3,117 ft)

The following section defines the limits to help avoid IT equipment damage and/or failure from particulates and gaseous contamination. If the levels of particulates or gaseous pollution are beyond the specified limits and cause equipment damage or failure, you may need to rectify the environmental conditions. Remediation of environmental conditions is the responsibility of the customer.

Particulate contamination

Specifications

Air filtration

Data center air filtration as defined by ISO Class 8 per ISO 14644-1 with a 95% upper confidence limit.

NOTE Applies to data center environments only. Air filtration requirements do not apply to IT equipment designed to be used outside a data center, in environments such as an office or factory floor.

NOTE Air entering the data center must have MERV11 or MERV13 filtration.

Conductive dust

Air must be free of conductive dust, zinc whiskers, or other conductive particles.

NOTE Applies to data center and non-data center environments.

Corrosive dust

• Air must be free of corrosive dust.
• Residual dust present in the air must have a deliquescent point less than 60% relative humidity.

NOTE Applies to data center and non-data center environments.

Gaseous contamination

Specifications

Copper coupon corrosion rate

<300 Å/month per Class G1 as defined by ANSI/ISA71.04-1985.

Silver coupon corrosion rate

<200 Å/month as defined by AHSRAE TC9.9.